If your truck has a 2" lift, this spacer kit lets you keep your truck at its lifted height while still getting the full support of Pacbrake's air suspension system.Highlights 2" Lifted Vehicle Compatibility: Spacer kit allows Pacbrake 5000-lb air springs to be used on lifted trucks without sacrificing ride height. Built for Air Spring Performance: Designed for single and double convoluted air spring kits to maintain correct suspension geometry.
Short 2-1/4" spring hangers can leave the front and rear axles sitting higher than the center axle on a triple-axle Comfort Ride system. These spacers lower the outer axles to restore proper alignment and even load distribution.This helps distribute trailer weight more evenly and can reduce poor tracking, suspension stress, and premature tire wear. Indexes into the Suspension for Proper Alignment Each spacer uses a top indexing hole that mates with the slipper spring nut and a bottom locating stud that fits into the axle saddle. These locating points help keep the spacer positioned correctly and maintain the intended suspension geometry.
If your truck has a 4" lift, this spacer kit lets you keep your truck at its lifted height while still getting the full support of Pacbrake's air suspension system.Highlights 4" Lifted Vehicle Compatibility: Spacer kit allows Pacbrake 5000-lb air springs to be used on lifted trucks without sacrificing ride height. Built for Air Spring Performance: Designed for single and double convoluted air spring kits to maintain correct suspension geometry.
... Microcellular urethane springs cushion bumps and support rear loads to level your ride and minimize sway. Included 1" spacers accommodate lifted Jeeps.Features: Helper springs upgrade your vehicle's rear suspension for improved control and comfort Keep your Jeep level when you're towing or hauling a heavy load Help to absorb bumps and shocks Minimize sway 1" Spacers are included to accommodate your lifted Jeep Progressive load control - springs compress according to the weight of your cargo Lighter loads - springs compress easily at first for soft engagement and a less bumpy ride Heavier loads - springs compress by as much as 80 percent for support Durable microcellular urethane Works in temperatures from -25 F to 200 F Resists damage caused by oils, road salts, and UV rays Minimal lateral expansion - springs expand and compress vertically instead of to the sides so they aren't easily damaged when operating in tight spaces Maintenance-free - no tubing to run or air pressure to monitor like with air springs No-drill bolt-on installation - springs replace factory bump stops 2 Springs, lift spacers, and necessary hardware included Made in the USA Specs: Weight capacity (at 50-percent compression): 1,000 lbs SumoSprings will not increase your vehicle's weight-carrying capacity Height of lift spacers: 1" Limited lifetime warranty 30-Day satisfaction guarantee SumoSprings work to improve your vehicle's rear suspension. 1" lift spacers are included to accommodate your lifted Jeep.
This Tacoma Spacer kit may be required with the purchase of HP10328 Pacbrake Air Spring Kit (sold separately) compatible with Toyota Tacoma / PreRunner.
Hey Eric. Welcome back and congrats on the new SUV. The Curt item #C26VV is listed as fitting the 2026 Grand Highlander but I have a better option for your 2026 Grand Highlander Hybrid Limited. It's our etailer item #e69ZV. We've actually…
If the inside of your trailer tire is rubbing against the frame on your trailer then you can either get a new trailer axle that has a larger hub-face measurement or get slightly smaller tires. The easier solution would be to swap out your tires for…
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
Installing a 4,000 lb capacity leaf spring on a trailer with a 3,500 lb capacity axle will make the suspension stiffer which could then in turn minimize the risk of the axle contacting the frame. However, this is not what I recommend to fix your…
Timbren likes to recommend 1 inch between the axle and the Timbren when the truck is unloaded. We have found that this works the best. This allows the suspension to feel when the vehicle is unloaded and still gives you support when needed when…
In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…
The size of a Bearing Buddy will not be enough to determine the replacement bearings you need. In order to find the correct wheel bearings, you need take apart your hub assembly and looking at the bearings themselves; wipe away the grease and you…
I wasn't able to find anything in regard to a replacement part for your TDE 11029C hub assembly, but if you can pull your hub and either look for bearing/grease seal parts numbers or measure the different locations on your spindle then I can see…
Yes, we do have a couple of idler hubs that fit the item #L44649 inner and outer bearings on your Venture boat trailer. They come in two different lug pattern sizes and are designed specifically for boat trailers. I couldn't get any information…
We don't carry your specific snow plow, but we do have a couple of skid show options that may work for your plow. We have the Replacement Standard Shoe Assembly for Western Snowplow #3371303200C you asked from, but we also have other options.…
We have an option for you, though there isn't a way to get matching keys for a Master Lock #2848DAT trailer hitch and coupler lock set as they don't have a Keyed Alike option for a second set. What you can do in order to use the same key for…
I have a solution for you but I'm not aware of a bolt on safety chain bracket or clevis. However you can simply take a safety chain set like the 42" Long Safety Chain with 3/8" Clevis Hook (15,000 lbs) #337BSC3842 and use a grade 8 bolt…
... The tall microcellular urethane springs absorb big bumps and shocks and engage sooner than standard springs. Includes 1" spacers.Features: Off-road helper springs upgrade your vehicle's front suspension for improved control and comfort Absorb big bumps and shocks that can occur when driving over rough terrain Minimize sway for better control when rock crawling Support heavy front-end loads (like winches or aftermarket bumpers) to keep your Jeep level Faster activation - springs are taller so that they engage more quickly than standard helper springs 1" Spacers are included to accommodate your lifted Jeep Progressive load control - springs compress according to the weight of your cargo Lighter loads - springs compress easily at first for soft engagement and a less bumpy ride Heavier loads - springs compress by as much as 80 percent for support Durable, high-density microcellular urethane Works in temperatures from -25 F to 200 F Resists damage caused by oils, road salts, and UV rays Minimal lateral expansion - springs expand and compress vertically instead of to the sides so they aren't easily damaged when operating in tight spaces Maintenance-free - no tubing to run or air pressure to monitor like with air springs No-drill bolt-on installation 2 Springs, lift spacers, and necessary hardware included Made in the USA Specs: Weight capacity (at 50-percent compression): 1,400 lbs SumoSprings will not increase your vehicle's weight-carrying capacity Height of lift spacers: 1" Limited lifetime warranty 30-Day satisfaction guarantee SumoSprings work to improve your vehicle's front suspension. 1" lift spacers are included to accommodate your lifted Jeep.
Install your fifth-wheel trailer hitch with this all-inclusive kit. Spacers ensure proper spacing between your truck's frame and bed. Includes 10-bolt base rails, universal brackets, spacers, and necessary hardware.Features: Universal brackets mount beneath your truck bed to provide attachment points for 5th-wheel rails 10-Bolt base rails sit in the truck bed and allow installation of your above-bed 5th-wheel trailer hitch Spacers provide the required 1/2" spacing between the frame and truck bed, preventing damage to the bed when you torque the bolts Sturdy, powder-coated steel resists corrosion Kit includes base rails, brackets, spacers, and mounting hardware Compatible hitches - B&W Patriot, Curt, Draw-Tite, Hidden Hitch, Husky, Reese, and Valley Made in the USA Limited lifetime warranty
... Without the right bump stop spacing, your shocks can go solid on full compression. This front spacer kit helps protect your shocks and keeps your suspension working safely - even with upsized tires.
When coil springs compress too far, they can go solid, causing a harsh ride and potential damage. This rear bump stop spacer kit limits travel just enough to keep your springs working like they should, even when fully loaded.
Lifting your suspension can lead to bottomed-out shocks if the bump stops aren't adjusted. This spacer kit helps limit suspension compression, protecting your shocks from damage when the trail gets rough.Highlights Prevents Shock Overtravel: Helps stop the suspension before the shock bottoms out protecting internal components. Front and Rear Coverage: Includes spacers to limit compression at both ends of the vehicle. Ideal for Lifted Vehicles: Especially important when installing long-travel shocks or taller springs.
Lifting your rig can push your coil springs to the limit - literally. This rear bump stop spacer kit helps prevent the springs from going solid at full compression, protecting your ride quality and suspension components.
Lifting your rear suspension can pull the driveshaft too far from the diff flange, causing vibration or poor engagement. This spacer restores the right fit, so your driveshaft stays secure and runs smooth.
Install your fifth-wheel trailer hitch with this all-inclusive kit. Spacers ensure proper spacing between your truck's frame and bed. Includes 10-bolt base rails, universal brackets, spacers, and necessary hardware.Features: Universal brackets mount beneath your truck bed to provide attachment points for 5th-wheel rails 10-Bolt base rails sit in the truck bed and allow installation of your above-bed 5th-wheel trailer hitch Spacers provide the required 1/2" spacing between the frame and truck bed, preventing damage to the bed when you torque the bolts Sturdy, powder-coated steel resists corrosion Kit includes base rails, brackets, spacers, and mounting hardware Compatible hitches - B&W Patriot, Curt, Draw-Tite, Hidden Hitch, Husky, Reese, and Valley Made in the USA Limited lifetime warranty
If your truck has a 6" lift, this spacer kit lets you keep your truck at its lifted height while still getting the full support of Pacbrake's air suspension system.Highlights 6" Lifted Vehicle Compatibility: Spacer kit allows Pacbrake 5000-lb air springs to be used on lifted trucks without sacrificing ride height. Built for Air Spring Performance: Designed for single and double convoluted air spring kits to maintain correct suspension geometry.
Install Ride-Rite air springs on a lifted vehicle with these lift spacers. Spacers attach between the bottom of the lower bracket and the bottom of the spring on vehicles with a 2" lift. Kit fits air springs that mount on axle or leaf stack.Features: Allow air springs to be installed on vehicles with 2" lift Distance between upper and lower brackets must be between 7.5" and 8.5" Spacer must be same size as lift kit rise Include 2 lift spacers and all hardware necessary for installation Lift spacer fits axle- and leaf-mounted air springs Specs: Application: Vehicles with 2" lift and from 7.5" to 8.5" between upper and lower brackets Will not fit Ride-Rite models F2350 or F2286 Will fit Ride-Rite model F2286 if manufactured after Feb. 1, 2006 2-Year limited warranty
Install Ride-Rite air springs on a lifted vehicle with these lift spacers. Spacers attach between the bottom of the lower bracket and the bottom of the spring on vehicles with a 3" lift. Kit fits air springs that mount on leaf stacks.Features: Allow air springs to be installed on vehicles with 3" lift Distance between upper and lower brackets must be between 8.5" and 9.5" Spacer must be same size as lift kit rise Include 2 lift spacers and all hardware necessary for installation Lift spacer fits leaf-mounted air springs Specs: Application: Vehicles with 3" lift and from 8.5" to 9.5" between upper and lower brackets Will not fit Ride-Rite models F2350 or F2286 Will fit Ride-Rite model F2286 if manufactured after Feb. 1, 2006 2-Year limited warranty
Install Ride-Rite air springs on a lifted vehicle with these lift spacers. Spacers attach between the bottom of the lower bracket and the bottom of the spring on vehicles with a 4" lift. Kit fits air springs that mount on the leaf stack.Features: Allow air springs to be installed on vehicles with 4" lift Distance between upper and lower brackets must be between 9.5" and 10.5" Spacer must be same size as lift kit rise Include 2 lift spacers and all hardware necessary for installation Lift spacer fits leaf-mounted air springs Specs: Application: Vehicles with 4" lift and from 9.5" to 10.5" between upper and lower brackets Will not fit Ride-Rite models F2350 or F2286 Will fit Ride-Rite model F2286 if manufactured after Feb. 1, 2006 2-Year limited warranty
Install Ride-Rite air springs on a lifted vehicle with these lift spacers. Spacers attach between the bottom of the lower bracket and the bottom of the air spring on vehicles with a 6" lift. Kit fits air springs that mount on the leaf stack.Features: Allow air springs to be installed on vehicles with 6" lift Distance between upper and lower brackets must be between 11.5" and 12.5" Spacer must be same size as lift kit rise Include 2 lift spacers and all hardware necessary for installation Lift spacer fits leaf-mounted air springs Specs: Application: Vehicles with 6" lift and from 11.5" to 12.5" between upper and lower brackets Will not fit Ride-Rite models F2350 or F2286 Will fit Ride-Rite model F2286 if manufactured after Feb. 1, 2006 2-Year limited warranty
Install Ride-Rite air springs on a lifted vehicle with these lift spacers. Spacers attach between the bottom of the lower bracket and the bottom of the spring on vehicles with a 1-1/4" lift. Kit fits air springs that mount on the axle.Features: Allow air springs to be installed on vehicles with 1-1/4" lift Distance between upper and lower brackets must be between 6-1/2" and 7-1/2" Spacer must be same size as lift kit rise Include 2 lift spacers and all hardware necessary for installation Lift spacer fits axle-mounted air springs Specs: Application: Vehicles with 1-1/4" lift and from 6-1/2" to 7-1/2" between upper and lower brackets Will not fit Ride-Rite models F2350 or F2286 Will fit Ride-Rite model F2286 if manufactured after Feb. 1, 2006 2-Year limited warranty
... Includes (2) 1" rubber spacers, (2) 1/2" rubber spacers, and all necessary hardware.Features: Designed to adapt your Timbren suspension enhancement system (FR250SDE, FR250SDF, FR350SDE or FR350SDF) to your lifted vehicle Measure between the frame of your truck when empty and the rear leaf spring to determine if you need the spacer kit Fills space between your suspension system and lifted frame Includes (2) 1" rubber spacers, (2) 1/2" rubber spacers, and all necessary hardware Mix and match spacer sizes to fit your vehicle Fits: Timbren suspension enhancement system: FR250SDE, FR250SDF, FR350SDE and FR350SDF
This spacer kit is designed to adapt your Timbren suspension enhancement system (FRTT350F) to your lifted vehicle. Includes (2) 1" rubber spacers, (2) 1/2" rubber spacers, and all necessary hardware.Features: Designed to adapt your Timbren suspension enhancement system (FRTT350F) to your lifted vehicle Measure between the frame of your truck when empty and the rear leaf spring to determine if you need the spacer kit Fills space between your suspension system and lifted frame Includes (2) 1" rubber spacers, (2) 1/2" rubber spacers, and all necessary hardware Mix and match spacer sizes to fit your vehicle Fits: Timbren suspension enhancement system: FRTT350F
This spacer kit is designed to adapt your Timbren suspension enhancement system (TORTTN) to your lifted vehicle. Includes (2) 1" rubber spacers, (2) 1/2" rubber spacers, and all necessary hardware.Features: Designed to adapt your Timbren suspension enhancement system (TORTTN) to your lifted vehicle Measure between the frame of your truck when empty and the rear leaf spring to determine if you need the spacer kit Required for measurements between 6" and 7-1/2" Fills space between your suspension system and lifted frame Includes (2) 1" rubber spacers, (2) 1/2" rubber spacers, and all necessary hardware Mix and match spacer sizes to fit your vehicle Fits: Timbren suspension enhancement system: TORTTN
This Air Lift level spacer kit lets you add air springs to your lifted vehicle. These steel spacers go between the air springs and the mounting brackets, filling the gap between the air springs and your lifted suspension.The spacers are installed between the air bags and the mounting brackets, closing the gap between your frame and your OEM suspension. The spacers work with Air Lift's LoadLifter 5000 and LoadLifter 7500 XL, as well as other brands such as Firestone.
Filters
