Install this hub-and-drum assembly on your trailer. For electric or hydraulic brakes. Fits 5.2K and 6K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (25580) and race, outer bearing (15123) and race, grease seal, cap and nuts included.
Hub is designed for use on trailer idler axles. Fits 3,500-lb axles with #84 spindles. Inner bearing (L68149) and race, outer bearing (L44649) and race, grease seal, grease cap, wheel bolts, and lug nuts included. Pre-greased for easy installation.
Hub is designed for use on trailer idler axles. Fits 2,000-lb axles with BT8 spindles. Inner bearing (L44643) and race, outer bearing (L44643) and race, grease seal, grease cap, and lug nuts included.
In order to choose the correct Lock N Roll Articulating Trailer Hitch you'll need to measure from the ground to the center of the trailer hitch on the vehicle and then from the ground to the top of the frame on the trailer and subtract 1" -…
To convert the ramp door on your Wells Cargo Car Hauler to swing or barn doors, you will need some hinges and a latch. A lockable latch like the Polar Hardware Cam-Action Door Latch Kit #383200 is a great option. This system features a bridge-type…
You could install disc brakes on the Timbren Axle-Less Suspension #ASR5200S01. You would use one of the kits from the link I have included to the right. All of these kits have a 6 on 5-1/2 bolt pattern. The kits linked take the same inner bearing but…
The spindle diameter of the Timbren kit part #ASR35HDS02 where the seal rides is definitely 2.25 inch so to go with a disc brake setup for this setup will require a hub that has that size seal. That said, the Kodiak Disc brake kit part #K2HR526DKG…
To get the 5 on 5 bolt pattern, you will need the Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased #84550BX or the Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles - 10" Diameter - 5 on 5 - Pre Greased…
The only Timbren Heavy-Duty Axle-Less Trailer Suspension which allows you to obtain hubs/drums with a 5 on 5" bolt pattern is part #ASR35HDS02 which is rated for 3,500 lbs. In order to obtain this bolt pattern with brakes you'll need the…
You'll want to run the amount of amperage of circuit protection that your camper would need. If your RV was designed for 50 amp power and you were using a 30 amp power supply your 50 amp protection would prevent anything from surging over 50…
You will always use a surge protector matched to the TT's rating of 30 amps. I recommend the Power Watchdog the 30 amp Surge Protector with Bluetooth #HU97FR. You can use the free smartphone app to monitor your system and get notified if low or…
I have attached the dimensional drawings of the Timbren Heavy-Duty Axle-Less Trailer Suspension part #ASR35HDS02 for you. This system has a weight capacity of 3,500 lbs and is designed for single and dual axle trailers. It has a 5 bolt brake mounting…
Yes, it's possible to upgrade the suspension on this trailer for one with independent movements, an upgraded capacity, and disc brakes. That said, it won't be cheap and it won't be easy. However, if you have the funds and are willing to…
All of the parts you mentioned would work great with each other. You didn't mention the part numbers but I was able to determine what you were looking at based on title. The Timbren kit looks to be the part #TASR35HDS11 Hubs #AKHD-655-6-EZ-K…
I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…
Filter Results
