Result: knobs

Be sure to determine a location on the dash where you will be mounting the actual controller knob so the cable from the control knob can reach the control module mounting location under the dash. | Thanks...

The main unit mounts out of site so only the control knob is visible in the cab. The knob controls the braking power and also acts as the manual override. | Do you have a 7 pin flat trailer wire harness for...

But after I dialed up the power knob to greater than minimum, the unit read flashing n.c. | I had trouble pairing the Prodigy RF. After going through all the steps, the readout on the remote unit never was 0.0 and continued...

To correct this, rotate the level knob counter-clockwise, away from you. Repeat these steps until your desired braking is achieved. | i am just wondering why i would need to replace the stock 7-Way Connector to a new one. i...

If you have one of those empty spots in the dash, you can use a Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 to install the knob. *Since your vehicle does not have the factory tow package you will need to splice in the brake controller. |

This will provide you with a sleek proportional brake controller knob that doesn't need a bulky controller in your Crosstrek. | Hi, I need a 7 pin wiring harness, brake controller, and bracket ? to plug the trailer into for...

The Tow-Pro Elite brake controller is pretty unique because it can be installed virtually anywhere and you only need access to the 3/4" diameter control knob. The control knob has LED lighting integrated into it that changes colors depending on what settings you have chosen. |

It is a small knob that does not take up much room with the bulk of the controller mounted behind the dash. | I'm getting ready to install your receiver # e83ZR on my 2022 Subaru Forester for pulling my camping trailer. This...

This would allow you to use a trailer brake controller like the Redarc Tow-Pro Liberty Brake Controller # RED24FR, which is going to have a sleek control knob instead of a big bulky controller. You will need the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers # RED69FR for installation and can use the Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 to provide a more factory like appearance. |

The trailer brakes are adjusted using the control knob which can be mounted within reach of the driver. | I need a complete towing package for my 2022 Toyota Highlander, hitch, wiring and brake controller. What parts are needed?...

I have tried the suggestion to have the power knob set higher than minimum step 6 but still n.c. flashing even after re-connecting the trailer to the power module. | I have a 2017 Volvo XC 90 with tow bar and wiring done by...

You'll control the trailer brakes via a knob that can be mounted anywhere within the drivers reach. | I need a wire harness for my 2016 Honda Pilot , Must be a 7 pin and have the ability to add a break controller later on if...

This unit is proportional and the main component is hidden behind your dash. The control knob can be mounted directly to the dash or with the Universal Mounting Panel # 331-TPSI-001 for a more factory appearance. | Greetings!...

Otherwise, if you're needing to ADD 4-Way and 7-Way sockets then you need the following parts: - Curt T-Connector Vehicle Wiring Harness # C58DR - Universal Installation Kit # ETBC7 - No-Drill Mount Bracket, Long # 18136 - Extra 10 Gauge Wire # 10-1-1 (on an as-needed basis) If you also need a brake controller then I really like the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness # RED52VR because it can be installed virtually anywhere and the control knob doesn't take up much space. This will splice in to the wiring you ran for the ETBC7. |

This controller has a small control knob which will mount to your dash and the main body of the unit will be hidden behind the dash for a clean look. | LOOKING TO INSTALL A TOW BAR ON A 2023 JEEP WRANGER SAHARA AND WAS LOOKING...

- Brake Controller: Last but not least, the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional # RED52VR. I really like how this controller has the knob on the dash so you can easily adjust the brakes, and also if you were ever in an emergency situation it is nice having that manual override right there |

If you have a blank switch space you can use part # 331-TPSI-002 to mount the control knob in the dash without having to drill any holes. | I have a 17 Toyota Hylander Limited w/o factory tow package. I need a 7 pin wiring...

I really like the Liberty brake controller because it can be installed virtually anywhere and then the control knob is small and out of the way so it won't be taking up space in your cab. | I have a 2020 Lexus GX 460 that didn’t...

Finally for the brake controller, I really like the Voyager iD because it can be installed so that all you see is the small control knob - this leaves you plenty of leg room without worrying about bumping into the controller. ...

The main unit will mount behind the dash with only a small control knob visible to adjust the braking force to the trailer brakes when needed. | Hello, I have a 2023 Grand Cherokee L Limited. I plan to get the Curt Class III...

For a brake controller I recommend the Redarc Tow-Pro Elite # RED44FR because it not only is a great controller, but it also installs out of the way and has a small knob that you use to adjust settings. Since space is typically limited in and around the dash of minivans nowadays the mounting convenience is invaluable. |

The brakes are adjusted using the control knob which can be mounted anywhere within the driver's reach. | I have a 2021 Nissan Armada, and I need to install a 7-way trailer connector and a brake controller. What parts will...

The universal kit comes with all of the wiring and connections you need for the install and the Prodigy iD is a reliable options that installs practically anywhere and looks like an OEM solution due to the design of the control knob. You'll also need a No-Drill Bracket # 18140 to secure the 7-Way back near the hitch receiver. |

Rather than using the cumbersome buckle and strap arrangement used by other racks, the Raceway uses 4 cables that can tighten with the twist of a knob, allowing the rack to install in moments. The rack can be locked to the vehicle, and the bikes can be locked to the rack to help deter theft. |