Result: parallel kit

Id like to lift the rv by 2 to 4 inches above the axles. I read a block 2 lift above the axle isnt good to do with the MORryde CRE3000 suspension. | I have a Grand Design 260RD fifth wheel, meant to be towed...

Can this system be used with the rough country block level kit in the front on a 2018 GMC Sierra 1500 Denali? | Can this system be used with the rough country block level kit in the front on...

As the RoadActive Suspension Custom Leaf Spring Enhancement Kit # RAS3611-Y will attach to the top of your leaf springs and your leveling blocks are installed under your leaf springs, there will no issues installing these. |

Would this work still with the 2” leveling block? Or what do you recommend? | I currently am driving a 2018 Toyota Tundra, TRD 4x4 with a leveling block for rear leaf spring 2”. Looking to add this unit to my...

I have an 11 inch height difference between my receiver and the D-ring connection at my aftermarket bumper on my 2014 Wrangler Unlimited. Is this acceptable, or do I need to elevate my connection point on the RV? | You will absolutely need...

Yes the RoadActive Suspension Custom Leaf Spring Enhancement Kit part # RAS4611 will work with your 2018 Nissan Titan with the leveling block installed. | I have a 2018 Nissan Titan sv 2wd....

My van /rv come with no sway bar how many inches is the hump stand out when the bar is parallel to the floor I have generator in the back my clearance is 3.5inch can I adust the bar down | My van /rv come with...

This comes with needed safety cables included and no need for high-low adapter on most setups as the adjustable head tilts up or down 3" to keep tow bar parallel with road during towing. A properly installed set up requires the tow bar to be within 3" of level. |

This diode kit allows you to use your Buick Envision's tail lights and wiring system while preventing feedback from your RV. | Any issues with this base plate for a AWD vehicle? Thanks | No, you'll be fine...

If the 12 volt supply wire is to be black to the connector and plug, then why do you only supply red wire for your RV and vehicle 12 volt supply kits? Shouldnt there be a black wire from the RV fuse block to the connector, and black wire from the plug to the vehicle fuse block? |

It sounds like you need a brake light relay kit. This kit is used to prevent the towed vehicles brake signal from overriding the turn signal from the RV when applying the brakes during a turn....

This diode kit allows you to use your Hyundai Veloster's tail lights and wiring system while preventing feedback from your RV and includes a 7-wire to 6-wire Flexo-Coil electrical cord and 6-way socket. |...

If you find that these will not work for you, you may want to consider something like the RoadActive Suspension Custom Leaf Spring Enhancement Kit - Heavy Duty # RAS3611-SLHD. This kit attaches to your leaf springs so the blocks will not impact the performance. |

I recommend installing a 4 way flat like the Hopkins Endurance, # HM48030, on the back of your RV. This will allow you to plug directly into the Roadmaster Universal Wiring Kit, # RM-154. | I will tow a 2010...

I have a frame leveling kit on the front end as well as a 1 inch block on the back. | I’ve seen several comments on how this kit will raise your truck bed a couple of inches. I have a frame...

This diode kit includes everything you need to connect your RV's tail, brake, and turn signal lights to your Chevrolet Sonic with variable voltage lights while flat towing. | I am thinking of purchasing a 2019...

Here are the rest of the parts you'll need to flat tow your 2024 Ford Maverick Hybrid: Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item # RM-520 and item # RM-643 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit - Removable Arms item # RM97RR Wiring Harness - Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267 Charge Line - Roadmaster Battery Charge Line Kit for Towed Vehicles item # RM-156-25 High Low Adapter - The tow bar needs to be within 3" of level. |

Will the RAS fit my 2016 F150 that has a 1inch lift block in the rear and 2.5inch leveling kit in the front? | Will the RAS fit my 2016 F150 that has a 1inch lift block in the rear and 2.5inch...

Both of these kits attach directly to your leaf spring and will not be affected by you removing the lift block while still offering 3000lbs of load level support like you were wanting for your gooseneck trailer. |

If that bracket is not blocking the openings on the crossover tube then # 118-3 is correct. | I have. 96 sidekick 2 dr 4+4 wnt to install base plate I have stowmaster 5000 tow bar the crossovertube is open with a bracket welded...

Also, the truck has bilsteins in the front at +2 inches and 1 inch rear blocks in the rear so it sits just about level when not towing. | I currently tow a 9-10K boat depending on fuel level with a 2016 3.5...

The head and shank also offer a bit of adjustability to help keep the tow bar level between the motorhome and Fit. Tow Bar Wiring Kit: Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267. |

Will these function properly with a 4inch lift kit installed on my 2009 Tundra 4x4 and how well will they level the truck under the load pictured? | Will these function properly with a 4inch lift kit installed...

This will let you run your Blue Ox tow bar in one receiver and mount your bike rack in another, while still allowing you to adjust for the correct drop to keep your tow bar level. To set it up, you would install the Gen-Y into the RV’s hitch, mount your tow bar in the receiver that keeps it level with the Jeep, and then use the upper receiver for your bike rack. |