!V70  x   >   EZ Connector  x   >  

do you have this in a 6way version? if not can you just leave a lead unhooked on both ends and still operate? | We do not have a 6-Way vehicle connector but we do have an adapter that will allow you to use one with the EZ Connector Magnetic...

Does this product work on 5th wheel trailors Trailor Harness breaks on sharp turns | The EZ Connector Pogo Trailer Cable Holder # 319-TCP011602 that you referenced can be installed on fifth wheel trailers like what you have but if you are...

My 2013 F250 has recently started displaying the trailer disconnected message. All lights on the trailer work including the brake lights. However when I test the brakes with the built in brake controller I have no brakes. It does this on every...

I’m looking to change the factory 4way/ 7way connector to an EZ connect plug . I want to mount the EZ connect in the factory hole in the bumper where the 4Way / 7 way is mounted. Is there an option to do this? It doesn’t look like it...

Which EZ Connector Magnetic 7 way should I get? 319-R7-02 319-R7-02D | Thanks for the pictures! Since your 2014 Toyota Tacoma has a 7-way connector that is hardwired in you will need to cut the wires from the factory connector and hardwire...

Since this is a pass-thru and the Curt ECHO Brake Controller is a pass thru will that cause issues? If I understand,I would plug the Curt ECHO into my 7 way and then using this adapter319-R7-51 plug it into the back of the CURT ECHO and then...

I purchased a Curt C55416 trailer electrical connector. Will it fit into the 319-S7-61 aluminum bracket? I know that the bracket needs to be drilled to mount the bracket to the vehicle. Does this bracket need to be drilled to install the connector...

I have a 2008 Chevrolet Silverado 3500 HD Cab/chassis with a flat bead installed. My gooseneck ball is located in a square well in the flat bed along with the trailer connection for the electrical. How much clearance is needed for the EZ Connector....

Can this be used on a snow plow | You can use the EZ Connector Magnetic 14-Pin Trailer Connector # 319-S14-05-6 for your snow plow as long as you do not exceed the ratings. This has a maximum voltage of 36 volts, max current on any single conductor...

Hello, Im looking for a 7 way trailer plug to 7 way round female end. I can send you pictures if need be. I dont see it on your page. Let me know if you can help me, thank you. | Yes, we do have what you are looking for it is the Pollak Trailer...

Is there an adapter to go to traditional 7way when using a vehicle without mag plug? | The EZ Connector Magnetic 14-Pin Trailer Connector # 319-S14-07-6 will fit inside the Trailer Connector Adapter # EZ94ZR and plug into a truck with a 7-way...

Question about correct pigtail set up for 2011 Toyota Landcruiser | The EZ Connector Magnetic 7-Way Trailer Connectors # 319-R7-02 is confirmed to fit your 2011 Toyota Land Cruiser. The trailer connector installs at the back of the vehicle and...

I am planning to switch my set up to use the EZ Connector 7 pin wiring. I have found the propper part that will let me as the receptive to the bed by tapping into the wiring for the 7 pin connector already in my bumper. The part that I am asking...

Good afternoon, We are getting ready to replace our old F250 with a newer F250 and we use it to tow a Featherlite horse trailer. The trailer uses the magnetic 7 pin connector and we have the female end in the bed of the truck on the left side...

On the EZ connector there are two models that appear to be the same. What is the difference between 319-S7-09 and 319-S7-09D Thank you | The difference between the two EZ Connectors is the trucks they fit. The # 319-S7-09D has the square...

Hi, Im looking at Item # 319-R7-05. Under the EZ Connector Wiring section of the product info, 0-5 feet long is stated, but under specs the length of the product is listed as 2 feet. Is this product available in a 5 foot length? Thank you. |...

I need to know what gauge wire or within this cable and where they all the same gauge often times will be 2 to 4 heavier gauge wires within the cable | I verified with the manufacturer that 16 gauge wire is used for each wire of the EZ Connector...

is there an option to replace the in-bed factory goosenck/5th wheel socket to the ez connector one on a 2022 f450? | The factory Ford connector in the bed of your 2022 Ford F-450 is rather unique and there is not a good way to just replace it...

Im wanting to purchase an EZ Connector adapters for my toy hauler and 2019 Tacoma. Im able to get the trailer adapter, but ez trailer website states the ez connector doesnt work on a 2019 Tacoma. Is there an option I can us for an ez connector,...

I have a lot of trouble with the brakes on my RV travel trailer. The brake controller randomly shows overload. The blades on the trailer side plug look tarnished and are spread apart without closing back together. I solved this by cleaning and...

I am thinking of replacing my 7 pin connector on my 2005 F350 Super Duty with the EZ-Connector magnetic. Do you stock a seven pin adaptor to fit the magnetic connector so if I use another trailer with 7 pin Ill have the adaptor. | Yes, we have...

Is this truly wired with 16 gauge across the board? Id be interested in using it to replace the 7 pin connector I have on my truck and trailer now, but the current connector has a mix 14, 12, and 10 gauge wiring which I believe is standard to...

I just bought 2004 Lancer truckbed camper. I need a adapter from the camper to my standard 7 pin rv connector.if you need I can send you a pic of the lug. | Hey Mike, thanks for reaching out! I don't know why Lance chose to make their own...

I have a Nighthawk Towing hitch and I’d like to convert the plugs to magnetic connectors. I have a 7-way connector on my RV and a 6-pin connector on my Jeep. What would be a setup that would work for my install? | To use a magnetic connector...