Result:

2025 Grand Design Imagine XLS TT: Need new entry door keeper. There are two that look what we have: RD38ZR and 37210625. One has measurements, the other does not. Whats the difference, other than price? Not sure which one to order. | Thanks...

Hello, we are looking to install 110 outlets in our mini buses which is not equipped with. Do you have a install kit for it. each bus will have 18 outlets behind pass seats. | Hey Abdul, we have 110 outlets like the part # RD26FR which you could...

Hello, I see this switch has what i would call spring tabs, so will it fit a cut out of .975 wide x 1.65inch tall? I am trying to find a replacement switch for my awning. My current switch looks identical to this one, but not sure it will fit...

I want to replace baggage door handle 12055-37 on 1999 Southwind Fleetwood F53 motorhome and latch RD26MR. Can you help me with this? Thanks Larry | Hey Larry, yes the RV Designer Door Latch part # RD26MR will work great to replace the 12055-37...

What size is the hole it needs? this will be a new install for me. | Hi Keith, The RV Designer Round Low-Profile Cable Hatch part # RD46GR fits into a cutout that is 3 1/2" in diameter. The overall flange dimensions are 4.6" x 2.6". You may...

Hello...I am looking for a Trailer Tail-light side lens cover...all I need is the red lens cover because I have one that is missing... the other one that I measured is 2 1/4inch wide and 3inch tall...Just so that you know kind of what I am talking...

Hello, I’m looking to replace my 1996 Casita tail lights, I’ve been searching on your site and can’t seem to find the correct size lights that would match the mounting holes. Here are the dimensions, housing light L 8 9/16” x W 4 5/8“ and mounting...

We have a 1978 starmate and the door latch no longer stays latched. We have tried the JR replacement but the striker is too short. It’s not long enough to latch onto the door frame. How does the striker plate work? | Hey Angelique, I attached...

I have a micro mini Winnie camper 2022 model 2108 flxTB. I am looking for the divider privacy curtain and the connectors to it to go to the track. Do you carry the curtain? Thank you Jan | Hi Jan, At this time, we don't offer curtain fabric,...

What size ball end does this strut fit? | Hey Myrl, the RV Designers Gas Strut part # RD82RR that you referenced is designed to fit 10 mm ball ends. Where are you wanting to install this strut? |

Hello, I am looking for some standard on/off rocker swtiches for my 2025 keystone cougar that will fit in the factory cutouts on the control panel. These would be the same size switches as the factory awning and slide out controls. The cutout...

Is Part Number: RD86VR LED or incadescent? | Hi David, I reached out to RV Designer directly and they informed me that the RV Designer Indicator Light part # RD86VR is in fact an incandescent light. Are you looking to replace your indicator...

Thor 2016 Freedom Elite. Side entry door. What material is the door latch itself made of? Is it cheap pot metal or steel? I ask because all replacements I have ordered, break inside of three months. Thanks. | Hey Dave. The T5079 RV Designer...

Can you tell me the spacing of the screw holes on this door catch? The one Im replacing has a spacing of about 1 1/4 inches. Ill post a photo below. Thanks! | Hello Ken, Looks like we have a winner! I couldn't find that measurement anywhere...

I would like to use gas struts to raise my bed so that I can get into the storage area under the bed. What do I need to do to measure to decide what length I would need? Also, I would need a latch that would hold the gas struts down until released?...

What is the diameter of the slider the male part that fits into the track?? | Hi Michael, The RV Designer Sew-In Carrier part # RD48QR has the following dimensions: -Head is 3/16" in diameter -Post under the head of the carrier is 1/8"...

Were needing to replace the exterior trim on our 2021 KZ Escape trailer and Im not sure if the 1 is the correct size. Im looking at the RV Designer Heavy-Duty Vinyl Trim - 50 x 1 - Black. Can you tell me if thats what I need to purchase? Thanks...

Where does one measure from in order to match our existing cam locks? Thanks | Hey Kendra, you would want to measure from the back of the lock face to the base of the threaded body and the diameter of the hole that the latch fits into to pick...

I have a 1973 GMC Canyon lands RV… Not sure if this is the original curtain track but through a process of elimination I believe I have the type B track because it has wheeled carriers with hooks that attach to the curtains. I am wanting to...

Hello, I am getting a Valley 2 horse slant load trailer and I would like to add these lights around the trailer, on the outside. Is it possible to wire them to a switch? If so, what switch would work best? Thank you! Laurie | Hey Laurie, yes...

I’ve got a boat trailer at lake of the ozarks with a Dexter surge brake actuator, and the safety pin for the coupler latch has gone missing. Probably my doing after a day at the lake. The actuator still latches, but I don’t want to tow without...

Can I use this adapter to hookup an electric jack on my utility trailer? | Hey Jerry, we have what you are looking for with the replacement 7-way part # A7WCB which you could wire your trailer jack to and then plug it into your vehicle 7-way...

I have a 2013 Sienna LE AWD. Receiver is about 12” off the ground. My boat trailer tongue is level about 18” off ground. I need a riser rather than a . Can you help? Thanks. | Happy to help, Tom! Thanks for sharing your measurements, that...

I lost the snap pin that keeps my boat trailer coupler latch from popping up. I don’t need a locking one, just something quick to put in before towing. Is RD72GR enough for that? | Hey Monica! Yes, the RV Designer Safety Lock Pin # RD72GR is...