Result: Trailer Support

I am wondering which slide out supports I need for my travel trailer slide. The trailer has one slide and the dry weight is 6500, total capacity 8800. Should I buy the supports with the 6000 lb capacity? Not sure if the weight capacity is considering...

I have a 2015 range rover evoque and really like the look of the after market tow package from curt. I primarily will use the hitch to attach a swinging bike rack or other cargo carriers. Will I also need to use a strap to support a rack?...

I just purchased a electric A-frame Jack to replace manual jack on a 2012 chalet takena trailer. Instalation instructions say to install a lower support plate on frame if not already present. Is it common for a trailer to have this lower...

dont know where i would attach a support strap on the back of my fifth wheel camper all the picks show are support straps with cars. | The Curt Trailer Hitch Support Strap # 18050 can be attached on the safety chain loop of the Adjustable Width...

I see you do not reinstall the bumper support bracket. Why not? The hitch does not provide the same contact points that the bracket did i.e. 2 vs 3 and the frame tie in provided by the bracket is eliminated. I doubt Toyota added this bracket...

Are these suitable to support the four corners of a 8.5 x 20 enclosed trailer when it is not hooked to the tow vehicle? Want to use the trailer for storage and need something to stabilize the back / front of the trailer so the ramp can be used...

what is the difference between support capacity and Lift capacity | The support capacity is how much a jack can hold whereas the lift capacity is how much a jack can lift. The Bulldog Square Jack w/ Footplate part # BD190754 has a 8,000 lb support...

Hi, I have been told that the rollers support the weight of the boat since they contact the keel and the bunks are their to keep the boat latterly secure on the trailer. I just noticed a reply from Chris O. to a customer that said the opposite...

I’m looking for a leg support that swivel out of the way when not needed to put on back of 40ft trailer for support when loading and unloading. I prefer something I can swivel down pull pin leg to desire length and pin. | From your description,...

Will the TJB-2001S-B jack withstand the fatigue and vibration of a 300 lb active load during trailering? I am using two of these to support a 600 lb boat hull. One on each side raising and lowering the gunnel support columns. I had planned...

looking for a jack to just support slideout on a 28 ft. tow behind trailer. thanks | We have just what you are looking for. Ultra-Fab has two sizes of slide out supports - sold in quantities of 2 per package. The Ultra-Fab...

I have an old escort trailer that I need to make new bunks for but cant find anything that looks like my existing setup. I have 73inch between bunk support points so I worry without the extra support my current setup has I will not have enough...

What trailer support plate would work with the Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2 Ball - Weld On - 10K The coupler is longer by about 3 or 4 inches and would have to move the jack support frame down also. | For...

Hi there, We recently purchased a 2022 Jayco Jay Fight SLX 242BHS Travel Trailer. The stock bumper is without a Receiver Hitch for accommodating our bike rack, which is a Thule 4 Bike system that would require a 2inch Receiver Hitch. It...

In the Installation instructions I saw Failure to use support straps on trailer hitches with 1 1/4inch receiver tubes voids the trailer hitch and bike rack warranties. I have not seen this warning anywhere else in your information. What does...

Where can I find the support strap for the platform bike racks | If you have a Curt Class I or Class II 1-1/4 inch by 1-1/4 inch trailer hitch receiver, you would need the Curt trailer hitch support strap with a cambuckle, part # 18050. This...

i have a tracker 1448 alweld boat on a tracker trailer with 7 foot flat bunks will the 5 foot model work on this trailer. ?The boat and motor will not exceed 1500 pounds. If so how should they be placed? thanks, | Replacing your 7 foot bunks...

I have a 2013 Crawford Melonseed Skiff and a 14foot Haul Rite PWC trailer. The trailer has bunks installed and I want to also install keel rollers. Should the bunks or rollers support the weight of the boat? This small 14foot sailboat only...

The Curt hitch for a 2015 Forester needs a support strap for non-trailer loads like bike racks, etc. The other two hitches that fit a Forester Draw-tite and Hidden Hitch dont seem to need a support strap. Why not, since all three hitches have...

Can the base support of each leg of the ladder rack be drilled and secured with proper bolts and locking nuts to an aluminum trailer to allow for carrying other kayaks? If the length of the base support is 16 inches, what is the width? Thank...

I recently purchased this bicycle rack. It will be mounted on the Curt Hitch Receiver for RVs, Item # 13703. Auxiliary stabilizing straps are required. I was hoping you could recommend straps that can be secured to the hitch since there is nowhere...

Is it possible to mount part #SR15-C to an ATC aluminum trailer wall support? If so, what hardware should I use? Thanks, | It is possible to install the Brophy D-Ring Tie Down Anchor # SR15-C that you referenced to one of the wooden wall supports...

How wide is the support bar at the base for the Tongue Mounted Crossbar for Malone MicroSport Trailers - 78 Long? | Hi Tom, The width is 1-1/4 inches for the bottom support bar of the Tongue Mounted Crossbar for Malone MicroSport Trailers #...

Do you need to place a support jack under trailer before you remove gearbox ? My tube on the gear side did not retract the same amount as the non gearbox side. I suspect gearbox may need replaced. | If you can level your trailer it is not...