Recommended Jack Support Plate When Installing Demco A-Frame Trailer Coupler DM14791-97

Question

Question:

What trailer support plate would work with the Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2 Ball - Weld On - 10K The coupler is longer by about 3 or 4 inches and would have to move the jack support frame down also.

asked by: Stephen G

0

Expert Reply:

For the Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Primed - 2" Ball - Weld On - 10K # DM14791-97 you were looking at you can use the Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs # JSP-100 to replace your current jack support plate.

I included videos for each of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

We currently have 3 different trailer jack support plates. I have included other dimensions in the included photos except for #BDSPB50 which was not available. #DL22763 is 1/8 inch thick. #BD003135 is 1/8 inch thick. #BDSPB50 is 1/8 inch thick. The…

view full answer...

Answer 2

There really is no way of knowing if you have that lower support plate without you checking on your specific trailer. It seems to be kind of hit or miss as to whether you need the Bottom Support Plate #DL22763 so you can either purchase the support…

view full answer...

Answer 3

When installing a trailer coupler like the Etrailer A-Frame Trailer Coupler, part #CA5100B, you want the coupler right up against the edge of the trailer frame. This coupler is a weld-on coupler for A-frame trailers. I would recommend having a…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended Jack Support Plate When Installing Demco A-Frame Trailer Coupler DM14791-97

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching