Trailer Hitch and Wiring for 2009 Mercedes R320 Diesel
I have a 2009 mb R320 diesel w251 . The information on the web site indicates the class 2 trailer hitch and separate wiring packages are for a r350 MB the wiring package is with brake controller and 7 way. Can to clarify the correct products...
Looking for Hitch Solution for 2004 Monaco Dynasty Coach
Morning Have a customer looking for a trailer hitch assembly for their 2004 Monaco Dynasty coach Diesel pusher The original hitch appears to have been cut off with a torch Any help on this would be greatly appreciated | Hey Bill, I wish...
Bike Rack Recommendation for 2008 Infiniti G35 that Allows Rear Trunk Lid to Open
Hi, currently looking for a trunk mount for max 2 MTB Orbea Oiz on a 2008 Infiniti G35x. Ideally one that can stay on and allows trunk to open. Do you work with shops in the DMV area that install these? Thanks | Hey Kenneth, there isn't a trunk...
Tow Bar for 1981 Volkswagen Rabbit Pickup
What tow bar will hook up to a Volkswagen rabbit truck bumper, I need one that is 31 inches | Hi Andrew; are you saying you need the arms to be 31" apart? The Curt Adjustable Tow Bar # C19745 you were looking at has an adjustable arm width from...
Availability of an A-Frame Coupler that is 45 Degrees and Not 50 Degrees
Is there an A frame coupler that is NOT a 50* angle? I have an older stock trailer and it needs like a 45*. | All of the A-frame couplers we carry are for the standard 50 degree A-frames. What you could do, since your A-frame is a lower angle,...
Is Trailer Suspension U-Bolt Plate Supposed to Bend and What is Torque Spec for 3/8" U-Bolts
So, I noticed in the video the spring plate does bend when tightened. How much torque was used? This is normal on the spring plates? They should bend slightly? I freaked out after I noticed my bent. But this is how it should be? | Trailer...
Diagram of the Portion of the Fascia that Needs Trimmed to Install Curt Hitch # C13103
do you have a sketch of how much to trim do you cut around hitch support bar ? | I attached a copy of the installation instructions for the Curt hitch # C13103 which is confirmed your 2007 Mercedes R350. The installation instructions have...
Should Radial or Bias Tires be Used for a 3500lb GVWR Pop Up Camper Trailer
Vehicle - 2011 Coleman Sun Valley pop up camper. Fully loaded - 3500lbs I cant seem to figure out which tire to get. It seems there is much debate on trailer tires, whether to get radials or bias ply. My stock tires are Kenda ST185/80D13-D and...
Difficulty Hooking on Bottom Trunk Mount Bike Rack Straps to Truck or Hatch
Hello, my trunk is so tight there is not enough space for the hooks to fit at the bottom of the trunk lid for my 2007 Infinity G35. Attaching these hooks under the bumper is not an option because it is very soft and will pucker the bumper. I...
Is Cutiing Required for Installation of the Mercedes-Benz R350 Trailer Hitch # C13103
I would like to know if there is any cutting of the oem bumper required in order to fit your trailer hitches? | You will not need to cut the OEM bumper for installation of the Curt Trailer Hitch, item # C13103, for the 2008 R350 by Mercedes-Benz....
Trailer Hitch for a 2012 Mercedes R350 BlueTec
Will this hitch also fit the Mercedes 2012 R350 Blue Tech diesel model? Also, where is the best place to get the hitch installed once I buy it? I doubt that a dealer would do the work but I am afraid to trust non-Mercedes technicians, especially...
Removal of Fascia on Mercedes 2008 R350 When Installing a Curt Trailer Hitch, Part # C13103
Once I get the facia off, I can install the hitch. Any tips? Ive removed the 4 bolts under the rear bumper. How do I get the rest of the facia off? CURT 13103 model hitch. | I spoke with my contact at Curt and he informed me that the underbody...
Ground Clearance of Curt Hitch Installed on 2008 Mercedes Benz R320 CDI
Is the car just too low for a hitch? | For your 2008 Mercedes Benz R320 CDI we have the Curt hitch part # C13103 as a confirmed fit. This will fit your vehicle will and will not sit too low at all. When we installed this hitch on a similar 2006...
Availability of Hitch for 2006 Mercedes R500
Does this fit a 2006 Mercedes R500? | We offer two different Class III hitches that are a fit for your 2006 M/B R500. Both the Curt # C13103 and the Draw-Tite # 75470 offer a 3500 lb towing/ 350 lb tongue weight capacity, but the warranty requirements...
How to Correct Sagging Class I Hitch and Bike Rack on 2006 Infiniti G35 Coupe
Wondering if it is possible to have someone weld a higher class hitch to the frame on Infinity G35 coupe? Is this possible? Have a class I now and it is sagging badly Thanks! | Trailer hitch makers generally produce hitches that are designed...
Will the Thule Pulse XL Roof Cargo Box Fit on the Factory Crossbars on a 2011 Mercedes R350
Hi, I am planning to purchase the Mercedes Benz Basic Roof Rackinch for my 2011 R350. I would like a roof cargo carrier that will work with the Mercedes Benz rack. Will this box fit on the MB Basic Roof Rack?inch The MB Roof Rack has a channel...
Compatible Trailer Hitch Receiver to Fit 2003 Infiniti G35 M6 Coupe
I just want to know if a trailer hitch is avalaible for my g35 2003 M6. | The Curt # C11483 is designed to fit your 2003 Infiniti G35 coupe. There is some drilling and fascia trimming to install it but all the necessary hardware is included....
Can a 4-Bike Platform Bike Rack be Used on a 1-1/4 Inch Trailer Hitch on a 2011 Mercedes R350
I have a 2011 Mercedes R350 with a 1-1/4 inch hitch. the label on the OEM hitch states that the car has a 280 pound tongue weight. Can I use the Yakima holdup 2 rack with 1-1/4 inch hitch and add to it the Yakima holdup +2 2 bike add on? ...
Trailer Hitch and Ball Recommendation for 2005 Infiniti G35 Sedan
Hi i wanted to know I have a 2005 infiniti g35 sedan and I bought a small boat and i wanted to know what hitch do you guys recommend, and if you guys have 7/8 ball size. thanks | We do have the Curt hitch part # C11482 which you referenced that...
Installation Details for Installing the Curt Trailer Hitch, # 247482 on a 2005 Infiniti G35
have you guys done an install of this hitch on any of the 03-06 sedans? I heard the fishing part is a pain. thanks! | We have a couple of videos featuring an Infiniti G35 but no hitch installations. Fish Wiring can be a little cumbersome,...
How to Determine Which Replacement Axle is Needed for 1979 Avion Travel Trailer
I HAVE A 1979 AVION TRAVEL TRALER WITH 4 SEPERATE AXELS. THE SPINDEL IS BENT ON THE RIGHT FRONT AXEL, THEREFOR WEARING MY TIRE DOWN WITHIN 3,000 MILES. DO YOU HAVE ANY IDEA WERE I MIGHT PURCHASE AN AXEL? THANK YOU | In order to determine which...
Using a T2 Classic for 2 Inch Hitches with a 2005 Infiniti G35 Coupe with 1-1/4 Inch Curt Hitch
I have a infiniti G35 coupe. it also has the Factory Spoiler. also a Thule T2 Classic 2 Bike Platform Rack - 2. i know i would need a 1-1/4inch to 2inch adapter. the hitch for my model car says it needs a strap. how would it attach using this...
Solution for Carrying 95 lb E-Bike
I have an e-Cells ebike that weighs about 95 lbs. What rack will be adequate for it? I have a MB R500. | The highest rated e-bike rack we can only carry up to an 80 lb e-bike. We do not have anything aside from motorcycle carriers like the etrailer...
Torque Specifications to Install the Curt Hitch Receiver C13103 on a 2009 Mercedes-Benz R-Class
The torque setting was not in my instructions. What is the correct torque for the # C13103? | The M10 x 1.50 CL 10.9 fasteners will need to be torqued down to 45 lbs-ft and the 7/16" 59 lb-ft for the Curt Trailer Hitch Receiver # C13103. This...
Filter Your Search
Contact and Help