Does the Replacement Master Cylinder for Titan Aero Actuators Come with Snap Rings, Spring and Seals

Question

Question:

Does this assembly include the piston, snap ring, spring and seals within the master cylinder assembly behind the rubber boot shown in the picture? Thank you.

asked by: Peter L

0

Expert Reply:

The replacement master cylinder # T4395100 does come with the snap ring, spring, seals all behind the boot. I made a video showing what it looks like with the boot off.

expert reply by: Michael H

0

Answer 1

The Titan Replacement Master Cylinder Assembly #T4395100 is a direct replacement for Model 60 and Aero 7500 drum brake actuators. I measured this item and put the dimensions on the included photo. Overall assembled height including the filler cap is…

view full answer...

Answer 2

There is a full replacement master cylinder that also includes the filler cap, orifice fitting, and hardware. The correct part for your Model 60 with drum brakes is the following: - Replacement Master Cylinder Assembly #T4395100

view full answer...

Answer 3

The Titan 60ZX7000 brake actuator is a Model 60 actuator, and you do have the correct part for a replacement master cylinder: - Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 So this will work…

view full answer...

Answer 4

The DICO 189 you referenced is the older version of the Titan 60. You will want to replace the master cylinder with the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100. I've attached a video…

view full answer...

Answer 5

Thanks for the pictures! It looks like you have a TCIC 23361 master cylinder. The Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators item #T4395100 is the replacement for it. However, this is a drum brake master…

view full answer...

Answer 6

I spoke with my technical contact at Titan and showed him the photo that you sent in of your actuator. My contact confirmed that you actuator is a Model 60. The right replacement master cylinder for you will depend on what kind of brakes the actuator…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Does the Replacement Master Cylinder for Titan Aero Actuators Come with Snap Rings, Spring and Seals

Product Page this Question was Asked From

Continue Researching