Replacement Master Cylinder Kit 4395100 For Model 60 Actuator For Drum Brakes

Question

Question:

I am looking for a rebuild kit for a master cylinder 4395100 for a Titan model 60 drum brake actuator. Thank you

asked by: Ken

0

Expert Reply:

There is a full replacement master cylinder that also includes the filler cap, orifice fitting, and hardware. The correct part for your Model 60 with drum brakes is the following:

- Replacement Master Cylinder Assembly # T4395100

expert reply by: Kyle S

0

Answer 1

You are correct that the Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100 you were looking at is the replacement master cylinder for your older 23361. I included a video of the Titan #T4395100 for…

view full answer...

Answer 2

The Replacement Master Cylinder Assembly part #T4820000 is designed for Titan Model 60 Brake Actuators like what you have and is for disc brakes. Then for a replacement shock you'd need the part #T2336200 and you'd be set.

view full answer...

Answer 3

The Titan Model 60 will use the Replacement Cover Gasket for Titan Aero 7500 Master Cylinders #DX37FR. If you need the entire kit use Replacement Master Cylinder Assembly for Titan Model 60 and Aero 7500 Brake Actuators - Drum #T4395100.

view full answer...

Answer 4

I have attached an image from the operation manual for the Demco Hydraulic Brake Actuator #DM8669112 that details how to bleed the brakes. The process consists of first elevating the trailer tongue about 4 to 6 inches and then loosening or removing…

view full answer...

Answer 5

The Dexter Brake Actuator part #099-175-20 replaced the Titan 60 that has a master cylinder with a fitting at the end. The fitting is a 3/16 inverted flare where the brake lines connect to. You do not need an extra fitting when you use the actuator.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

Hey Tony, welcome back! The Titan Zinc-Plated Brake Actuator item #T43329007K you purchased has a plunger you can access for purposes of bleeding the system of air. You will want to remove the plate that surrounds the breakaway lever to access it.…

view full answer...

Replacement Master Cylinder Kit 4395100 For Model 60 Actuator For Drum Brakes

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching