What Rise/Drop Spacing Do the 3 Holes on the Lock N Roll Articulating Rise/Drop Hitch Provide

Question

Question:

Since this LNR has 3 stops what are they? It says max is 4.25, what are the other two?

asked by: Brett

0

Expert Reply:

The holes on the Lock N Roll # 336VS503505 are spaced 2" apart center on center, so you'll have 4.25" at the lowest/highest and then roughly 2" rise/drop and 0" rise/drop in the various positions it offers.

expert reply by: Erik B

0

click to enlarge

Answer 1

To utilize the Lock N Roll coupler system on your trailer you'll need one of the following styles: - A-Frame #336TS504 - Flat Plate #336TS514 - 2" Channel #336TS528 - 2-1/2" Channel #336TS506 - 3" Channel #336TS508 The part…

view full answer...

Answer 2

Yes, we carry the Lock N Roll Articulating Trailer Coupler for 2" Receivers in 3 different lengths. The #336TS510 you found is 9-3/4" from the hitch pin center hole to the center of the coupler head. We also have it in a 18-1/2" Length…

view full answer...

Answer 3

When Lock N Roll Measured the Articulating Hitch w/ 3-Position Channel #336VS503505 they state that they are measuring from the center of the receiver pin hole to the center of the trailer connector pin at 5-1/2". As this is generally not how…

view full answer...

Answer 4

I'm assuming you're speaking of a 2 inch drop on the ball mount you're currently using, is that correct? If so, the #336VS503505 Lock N Roll articulating ball mount you'd looked at would allow for a 2 inch drop to properly level your…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hello Paul, thanks for reaching out. The inside dimension of the Curt Heavy-Duty Dual Ball Attachment for Weight Distribution Shanks #C29NR is 2". It will work with any standard weight distribution shank. I edited a picture to illustrate.

view full answer...

Answer 9

Hey JD, The Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS88RR uses hitch pic lock #WS54CR, which has a shear strength capacity of 45,000lbs according to Weigh Safe.

view full answer...

Answer 10

Hey Dewain, we actually have a lock set specifically designed for use with the Bulletproof adjustable ball mount part #BPH77MR with the part #34061674-D. This comes with two locks for the platform of the ball mount and an additional lock for the…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

What Rise/Drop Spacing Do the 3 Holes on the Lock N Roll Articulating Rise/Drop Hitch Provide

Product Page this Question was Asked From

Continue Researching