How to Test Brake Magnet Amperage With Multimeter
Question:
The article titled Testing Trailer Brake Magnets for Proper Function lists specifications for the DC amp draw for 2, 4, and 6 brakes installed. For example, 4 12 brakes should draw 15 to 16 amps. The article also recommends use of the BTMT15 multimeter, however this multimeter - and most others like it - has a 10A DC range function setting. Does this mean that it allows 0 to 100A in 10A increments, or that it reads 0 to 10A? If it only reads 0 to 10A which is what I thought that setting allows, how does one do the test? Thanks.
asked by: Neal A
Expert Reply:
You are correct, the PT89ZR is only designed to measure up to 10A which will not allow you to measure for 4 or 6 brake magnets on a trailer. In this case I would recommend using a multimeter with a higher amperage rating or testing the magnets separately. At this time we do not carry a multimeter capable of testing more than 10A.
The next section of our brake magnet testing article details how to test each magnet separately to determine if one or more of the brake magnets on your trailer is defective.
To test individual brake magnets for proper function sever the magnet wires and connect the ammeter between the positive terminal of a 12 volt battery and one of the magnet wires, it does not matter which one, then connect the other magnet wire to the negative battery terminal. Check the amperage, if the amperage is greater than the specified amount then replace the magnet. If the reading is less than the specified amount, the leads are bad and the magnet should be replaced.
Product Page this Question was Asked From
Digital Multimeter with 42" Long Test Leads - LED Display
- Electrical Tools
- Testers
- Multimeter
- Yellow
- Performance Tool
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Setting up the Curt Custom Underbed OEM-Style Gooseneck Trailer Hitch on a 2019 Ram 2500
- Video: Install: Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector on a 2014 Ram 3500
- Shop: 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole Plug - GM, Ford, Ram, Toyota - 9' Long
- Shop: Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long
- Shop: Trailer Wiring
- Video: Let’s Check Out the AMPLock Trailer Coupler Lock for Atwood Gooseneck and Flat Nose Couplers
- Shop: AMPLock Trailer Coupler Lock for Atwood Gooseneck and Flat Nose Couplers - Ductile Cast Iron
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Search Results: gooseneck hitch
- Search Results: amplock
- Shop: Curt Custom Underbed OEM-Style Gooseneck Trailer Hitch - 35,000 lbs
- Shop: SoftStartRV Soft Start for Single Zone Air Conditioner Setup - Qty 1
- Search Results: bwts20066bmp
- Search Results: b&w puck
- Search Results: 34065041
- Search Results: bwts30048b
- Search Results: 605dat
- Shop: B&W Ball and Safety Chain Kit for Ram Underbed Gooseneck Trailer Hitch
- Q&A: Wire Size Butt Connectors is Needed to Connect Wiring for Electric Trailer Brakes
- Video: All You Need to Know About the Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles
- Video: Let’s Check Out the Dexter Trailer Hub & Drum Assembly for 3,500-lb Axles
- Video: Remove and Reinstall a Trailer Hub Review
- Q&A: Difference Between an Idler Hub and a Hub/Drum
- Q&A: Replacement Hubs and Drum Brakes For a 2021 NuCamp TaB Trailer Using Dexter Axle Parts
- Q&A: Can I Put Smaller Wheels And Tires On a 2019 NuCamp Tab 320 to Lower the Trailer 3 to 4?
- Q&A: Troubleshooting Overheating Hubs on a Trailer With New Bearings and Grease
- Q&A: Why are Electric Brakes Getting Hot on 98 Coleman Camper After Installation of New Brake Assemblies
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Wiring
