Replacement Grease Seal for the Timbren Axle Less System part # A12WS545

Question

Question:

I have finished building my tandem boat trailer for the sand with everything but the steel from you guys. While putting grease in the axles with a hand grease gun I blew out an oil seal. I pumped until I could see existing grease ooze through the bearing. Can you tell me what the number of the seal is. It is the Timbren Axel-less 1200 pound 5 on 4!/2. Thanks,

asked by: Dean A

0

Expert Reply:

The correct grease seal you would need for your Timbren Axle Less System part # A12WS545 that you have is the # 10-9.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 6

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 7

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 8

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 9

Hey Dan, The info you provided does tell us a bit about the axle but isn't enough to look up what components go with with it. With it being a 3,500lb axle it's probably a generic 3,500lb kit for the bearings and seals but I'd hate to not…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 12

I sure can Bob and thanks for the information! Since you have a Lippert 3,500 lbs axle you'll be able to use the Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles item #AKHD-545-35-EZ-K, you were looking at. These have a 5 on 4-1/2 lug nut…

view full answer...

Replacement Grease Seal for the Timbren Axle Less System part # A12WS545

Products Referenced in This Question

Continue Researching