Mounting Orientation of TJ01RT-HD Stabilizer Jack
Published 11/12/2014
Question:
Atwoods instruction sheet for this jack shows a pair of them mounted so that when folded up for storage their feet point toward each other Im uploading an image cropped from those instructions. Thats the only indication in the instructions as to how they should be oriented. It implies that they would be mounted so that they extend out the sides of the trailer instead of the rear. But all the videos Ive found for these and other jacks like them show the jacks extending out the rear of the trailer, so that when folded for storage they would be parallel to each other with their feet toward the front of the trailer. That orientation seems better to me, because trailers move forward and back, not sideways, but it bothers me that the Atwood instructions show the other, side-to-side orientation. Which is safest?
asked by: Jim M
Expert Reply:
There many possible ways to mount a stabilizer jack such as the # TJ01RT-HD you looked at. Mounting them in the orientation shown the diagram would tend to work a bit better to stabilize the trailer against side to side movement, while having the jacks parallel to the trailer frame members would do a better job stabilizing against fore/aft movement. However, mounting them as shown in the diagram would be pretty effective against movement both ways from normal movement in the trailer.
The 'safest' method of installation will really depend on the type of trailer. If you're talking about a camper, I believe either orientation would work okay. For a cargo trailer that will have stuff constantly moved in and out of it from the rear door, I'd mount the jacks to they're parallel to the trailer frame to protect more against fore and aft movement.
Product Page this Question was Asked From
Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
- Camper Jacks
- Pop Up Camper
- Teardrop Camper
- Travel Trailer
- Stabilizer Jacks
- Steel
- 0 - 1000 lbs
- Manual Jack
- 18 Inch Lift
- Bolt-On
- Weld-On
- 1 Jack
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: etrailer Enclosed Trailer Transition Plate - Universal - 1,000 lbs - Qty 1
- Shop: Enclosed Trailer Transition Plate - 81-3/4" Long - Steel - Qty 1
- Shop: BTBRV Magnetic Hitch Receiver Reducer Set - 3" to 2-1/2" & 2-1/2" to 2"
- Shop: Stabilizer Jacks - 6-1/4" Drop Leg Travel - 18" - 650 lbs - Qty 2
- Video: A Closer Look at the Stabilizer Jack
- Shop: RV Exterior Lighting
- Shop: Ark Drop Down Corner RV Stabilizer Jacks - 24" Long Corner Steadies - Silver - Qty 2
- Shop: Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs - Qty 1
- Shop: Loadstar ST235/75R15 Radial Off-Road Tire w/ 15" Black Mod Wheel - 5 on 4-1/2 - LR D
- Shop: RV Interior Lighting
- Video: All You Need to Know About the Redarc In-Vehicle BCDC Battery Charger
- Q&A: Looking For Off-Road Style Tire For 22' Travel Trailer
- Q&A: Can 205/75R15 Trailer Tires Be Replaced with 235/75R15 Off-Road Trailer Tires
- Video: Comprehensive Review: Stabilizer Jacks
- Q&A: Total Extended Length of TJ01RT-HD Stabilizer Jack
- Video: The Low-Down on the Mounting Bolts and Hardware for 10" Brake Assemblies
- Video: Let’s Check Out the Mounting Bolts and Hardware for 10" Brake Assemblies
- Video: Detailed Breakdown of the etrailer Electric Trailer Brakes
- Search Results: stabilizer jacks trailer jack
- Video: All About the Paneloc Spring Latch
- Q&A: Correct Round U-Bolts for 3,500 Lb Dexter Trailer Axle
- Q&A: Recommended Replacement Parts for a Travel Trailer With 3.5K Axles
- Q&A: Shackle Suspension Kit for Single Axle Trailer With 3,500 lb Axle
- Q&A: Dimensions Of Shackle Bolt For Dexter Single Axle Heavy Duty Suspension Kit # K71-403-00
- Search Results: 3500 bearings
- Article: Trailer Lighting Requirements
- Article: How to Accurately Measure Trailer Leaf Springs
- Article: Slipper Spring Trailer Suspension System Review
- Article: How to Raise Your Travel Trailer Height
- Search Results: trailer tire 215 75r14
on Camper Jacks
