Distance From Center Of Ball Coupler To Center Of Trailer Jack Hole On Bulldog Collar-Lok Coupler

Question

Question:

What is the distance from the center of the ball to the center of the jack hole on the bulldog 2-5/16inch aframe couplers versus the standard latch type aframe 2-5/16 couplers? Trying to shift the tongue jack further back on a v-nose enclosed trailer so I can lower my tailgate while stopped.

asked by: Lloyd

0

Expert Reply:

I went to our warehouse and took the measurement you asked about on the Bulldog Collar-Lok Coupler w/ Low-Profile Latch, part # BD028499.

I have attached a photo of the coupler with the measurement noted. It is 12 inches from the center of the ball coupler to the center of the hole the jack mounts through.

expert reply by: Jeffrey L

0

click to enlarge

Answer 1

The distance between the center of the ball hole to the center of the circle used for A-frame jacks on the part #BD44125W0317 that you referenced is 12-1/2 inches. I confirmed this with my contact at Bulldog. The advantages between the latching…

view full answer...

Answer 2

UFP was bought out by Dexter Axle a number of years ago and they've been phasing out those parts for a while now so I recommend swapping out your a-frame coupler to one that is currently being manufactured so if you need to replace anything in…

view full answer...

Answer 3

You'd just have to physically go out to your trailer and measure the angle. So to do this, you'd need to get a protractor or something similar and place it on the edge of the inside on one side of the trailer frame, and check to see if the…

view full answer...

Answer 4

Thanks so much for the photos, and there isn't a replacement for just the front coupler portion of the long-discontinued coupler you have. So in order to switch out from a 2" to a 2-5/16" coupler attachment, you will need to replace the…

view full answer...

Answer 5

If you're experiencing sway control issues, adding a friction sway control bar could be just what you need to get things under control. I recommend the Curt Friction Sway Control part #17200. In order to install the Curt Friction Sway Control…

view full answer...

Answer 6

So the standard angle for A-frame trailers where the two beams meet is 50 degrees. So while I can't get you a CAD drawing for the coupler part #CA-5400-B if you are trying to design your trailer to have the correct angle for the A-frame you…

view full answer...

Answer 7

I walked out to our warehouse and pulled the Redline A-Frame Trailer Coupler #CA5100B. At the widest point inside the coupler measured approximately 9-1/4 inches, the narrowest approximately 2 inches and 8 inches between those points. Check out the…

view full answer...

Answer 8

The Tuson Electronic Sway Control System for Electric Trailer Brakes #335TSC-1000 has installation instructions that give a placement location on the center of your trailer and 5-10 feet behind the hitch ball. The unit comes with a wiring harness so…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Distance From Center Of Ball Coupler To Center Of Trailer Jack Hole On Bulldog Collar-Lok Coupler

Continue Researching