RV Laundry Rack Recommendation

Question

Question:

im looking for a laundry drying rack to attach to the rear camper bumper. it need easy on and off.

asked by: Clarence D

0

Expert Reply:

While we don't have a rack that would attach to your rear bumper we do offer the Camco RV Wind Up Laundry Reel part # CAM51064. You can install this virtually anywhere pretty easily and can be wound back up when you are ready to move.

expert reply by: Jameson C

0

Answer 1

Hey Mark, I would try spraying the fittings and the lines (basically everything) with soapy water in a spray bottle and you'll see bubbles where the leak is. It's not abnormal for the lines to be movable but that would be the first place I…

view full answer...

Answer 2

The Wall Mounting Bracket for Flat Panel TVs - 13" to 27" Screens #MAF50 only comes as the kit and isn't available for just the wall plate, so you'd need to get 2 of these to use this same system in 2 different rooms. We also carry…

view full answer...

Answer 3

All of the towel rings we offer are installed by using mounting screws. I am not aware of any that do not use screws for mounting. I have attached a link to our product page for the towel rings we offer.

view full answer...

Answer 4

Yes, but you are going to have a harder time accessing the mounting hole that would then be under the bar when you are installing or removing the setup.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

Hey Wesley welcome back. I do indeed have dimensions for the Gen-Y Nomad 5th Wheel to Gooseneck Pin Box item #GY57ND. I attached the complete specs below. The C/L measurement is only 20.3" and to the back bolt is 29.08" on the Gen-Y Nomad…

view full answer...

RV Laundry Rack Recommendation

Continue Researching