Could Mounting Brackets of Gustafson RV Towel Bar Be Turned 90 Degrees

Question

Question:

Can the base plates for this towel bar be turned sideways if i dont have 3 inches to mount them vertically?

asked by: Michael J

0

Expert Reply:

Yes, but you are going to have a harder time accessing the mounting hole that would then be under the bar when you are installing or removing the setup.

expert reply by: Jameson C

0

Answer 1

All of the towel rings we offer are installed by using mounting screws. I am not aware of any that do not use screws for mounting. I have attached a link to our product page for the towel rings we offer.

view full answer...

Answer 2

Hey Mark, I would try spraying the fittings and the lines (basically everything) with soapy water in a spray bottle and you'll see bubbles where the leak is. It's not abnormal for the lines to be movable but that would be the first place I…

view full answer...

Answer 3

The Wall Mounting Bracket for Flat Panel TVs - 13" to 27" Screens #MAF50 only comes as the kit and isn't available for just the wall plate, so you'd need to get 2 of these to use this same system in 2 different rooms. We also carry…

view full answer...

Answer 4

While we don't have a rack that would attach to your rear bumper we do offer the Camco RV Wind Up Laundry Reel part #CAM51064. You can install this virtually anywhere pretty easily and can be wound back up when you are ready to move.

view full answer...

Answer 5

Hey Peter, the Reese Pro Bar part #RE34FR would work great for your 2021 Little Guy Mini Max and your Grand Highlander. This has the proper tongue weight rating for your trailer and as long as you are backing up mostly straight you can leave the bars…

view full answer...

Answer 6

Both the Curt TruTrack 2P Weight Distribution System #C69JR and Reese Pro Round Bar Weight Distribution #RE44FR are going to use a 2-5/16" Ball #C40030 with a 1-1/4" shank. You will want to use the 2" Ball #A-90 to switch to a 2"…

view full answer...

Answer 7

I see what you mean with the additional support bracket below the frame on your 2024 Keystone Hideout Sport 175BH travel trailer. I'm glad you reached out to us Peter as that is going to limit you on what you can use. With that additional…

view full answer...

Answer 8

Hey Craig, the biggest thing that causes trailer sway is not enough tongue weight relative to the total trailer weight. You need to have the tongue weight between 10 and 15 percent of the total trailer weight. Most likely your tongue weight is on the…

view full answer...

Answer 9

Hey Chad! What kind of camper do you have? The Reese Pro Round Bar Weight Distribution #RE34FR can be used with the shank flipped over in the rise position to get you the height you need. Also yes, you can swap out the hitch ball with the #A-90. Let…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Could Mounting Brackets of Gustafson RV Towel Bar Be Turned 90 Degrees

Continue Researching