Grease Cap Recommendation to Replace AL KO Part Number 363277

Question

Question:

Our scout troop has a Cargo Craft box trailer with an Al-Ko axel. I need to replace the EZ Lube cover. According to their manual they call it part number 363277. Can you please advise what I would need to order from your site? Many thanks,

asked by: Jim B

0

Expert Reply:

I did some digging and based on the part number you referenced you need grease caps that have an outer diameter of 1.986 inches. Because of that you would want the part # RG04-040.

expert reply by: Jameson C

0

Answer 1

The Replacement Center Cap for 15" Aluminum Hi-Spec Series 06 Wheels is #AM90091B or #AM90091 both of which are confirmed to fit your wheels. The 3.19 is the diameter of the pilot hole on the wheel itself were it fits over the hub for future…

view full answer...

Answer 2

These are the same assemblies just different part numbers. Our part #84546UC3-EZ is the same as the Dexter part number K08-247-94 you mentioned. These are Dexter assemblies they have just changed their part number. I've attached a review video as…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Hello again Jim, Thanks for writing in! You're looking at the correct seal. The GS-1719 DL and TRP markings are the important identifiers, and they match the Double Lip Grease Seal #58846 (or for 2 pack #RG06-050). The additional numbers, such as…

view full answer...

Answer 7

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a replacement. The hub…

view full answer...

Answer 8

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 9

Hey Shawn, thanks for reaching out. For the Trailer Buddy Vault assemblies in the #DX23ER kit, the measurement is taken at the base of the cap where is drives into the hub. The 2.328" measurement listed is the OD of the base of the cap. These…

view full answer...

Answer 10

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 11

Hey John, thank you for all of the info from your 3,500 lb trailer axle. The correct bearing kit would be the part #DX76ER that you referenced. Did you have a bearing fail or are you wanting to have a backup set on hand?

view full answer...

Grease Cap Recommendation to Replace AL KO Part Number 363277

Product Page this Question was Asked From

Continue Researching