License Plate Bracket for a 1992 Jayco Pop-up Trailer
Updated 08/17/2026 | Published 08/25/2014
Products Featured in This Question
Question:
I own a 1992 Jayco Camper Pop up Trailer. A License Plate Bracket under the left tail light broke and I lost my license plate. The bracket was a hard rubber mounted underneath the light. I am looking for a replacement of same type or any metal or zinc that will last. Please advise if I can replace that piece or if I need to replace the hold tail light housing.
asked by: Bobby T
Expert Reply:
We may not have the exact same license plate bracket as the one you lost on your Jayco trailer. But we do have quite a few that you could likely use.
Bracket # LP15SB is an excellent choice since it is metal and would be more durable and would not cause ground problems (if the tail light grounds through the mounting studs). It mounts on holes that are 2 inches apart on center.
If you happen to need a hole spacing that is 1-3/4 inches apart then you could use # LP20SB.
I have included a couple of pictures showing the key measurements and a link to the right to all of the brackets we carry.
Product Page this Question was Asked From
Trailer License Plate Mount Bracket, Heavy Duty Zinc Steel
- Accessories and Parts
- License Plates and Frames
- Mounting Hardware
- Brackets
- Optronics
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer License Plate Mount Bracket, Heavy Duty Zinc Steel
- Article: Most Popular Wheel Bearings
- Video: All You Need to Know About the Grease Seal
- Shop: LubriMatic Marine Trailer Wheel Bearing Grease - 3 oz. Cartridges - Qty 3
- Shop: Mounting Hardware for 10" Single Brake Assembly
- Shop: Hydraulic Trailer Brake - Uni-Servo - Free Backing - Dacromet - 10" - Right Hand - 3,500 lbs
- Shop: Grease Seal - Double Lip - I.D. 1.688" / O.D. 2.332" - Older UFP Hubs/Marine Axles - Qty 1
- Shop: Replacement Race L68110 for Bearing L68149 - Qty 1
- Shop: Replacement Race L44610 for Bearings L44643 and L44649 - Qty 1
- Video: Ultimate Overview of the Trailer License Plate Mount Bracket, Heavy Duty Zinc Steel
- Q&A: What is the Difference Between the Redline Grease Seal and Dexter Grease Seals?
- Q&A: Replacement License Plate Bracket for Triton Jet Ski Trailer
- Q&A: Distance Between Taillight Mounting Hole Dimensions on CE Smith Trailer License Plate Bracket
- Q&A: Would the Optronics Trailer License Plate Bracket part # LP15SB Replace a Wesbar 003201 Bracket
- Q&A: Dimensions of the Optronics # LP15SB
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Feature Breakdown: Trailer License Plate Mount Bracket, Heavy Duty Zinc Steel
- Video: Feature Breakdown: Cotter Pin
- Video: Review of etrailer Trailer Bearings Races Seals Caps - Hub Bearing Kit 3500LB Axle - BK2-100
- Video: What to Know About the LED Combination Tail Light for Trailers over 80" Wide
- Video: Complete Breakdown of the CE Smith Trailer License Plate Bracket
- Q&A: Replacement Boat Trailer Seal for a NOK AD2527E Grease Seal
- Q&A: Replacement For Atwood 83000, 83010 Drum Brake Actuator & 10 Inch Free Backing Drum Brakes
- Search Results: cotter pin
- Search Results: 44610
- Search Results: grease cap tool
- Search Results: l44610
- Search Results: l68110
- Search Results: 44649
- Search Results: license plates and frames
Dave
8/14/2026
Hi, If feasible I expect to use this bracket to mount both the license plate and a license plate camera and to insure the license plate camera and bracket will work with this bracket I need a few specific measurements that I don't see illustrated in the various images with measurements. I have a picture of the bracket from the Optronics site with the areas I need measurements I can forward to you if that is possible. It is in a JPEG format. Along with the measurements I need an idea of what the notch is for near the top center of the bracket. Is there by any chance a thin rubber cushion that goes between the two post mounting holes to minimize chance of rattle or noise between the bracket and trailer frame?