Pin Length When Latched for the Bolt-On Stainless Steel Spring Latch # SL716SS

Question

Question:

WHAT IS THE LENGTH OF THE PIN IN THE CLOSED POSITION? END OF PIN TO BRACKET SEE ATTACHED PICTURE. THANKS!

asked by: SHAWN

0

Expert Reply:

I went and pulled a Bolt-On Stainless Steel Spring Latch # SL716SS from our warehouse and measure the dimension you are looking for and found it to be 1-7/8 inches.

See the pic I attached, I added the dimension to the picture you submitted

expert reply by: Jameson C

0

click to enlarge

Answer 1

We have a latch that will help you secure your trailer gate when it is upright and should not interfere with the cables on the Gorilla-Lift #GL1. Redline makes a Bolt-On Stainless Steel Spring Latch #SL716SS that you can install in a vertical…

view full answer...

Answer 2

The spring loaded latch pin I recommend is the Redline Bolt-On Stainless Steel Spring Latch, part #SL716SS. This latch measures 6-3/4 inches overall and has 4 mounting holes. I have attached a photo of the latch pin with the dimensions shown you can…

view full answer...

Answer 3

Yes, there is a couple spring latches I recommend to hold up your gate for your 2013 Karavan 5x8 flat bed trailer. The Redline bolt-on stainless steel spring latch #SL716SS with aluminum base would be a fine choice. The pin diameter is 7/16 of an…

view full answer...

Answer 4

The distance from the mounting surface of the Bolt-On Stainless Steel Spring Latch #SL716SS to the center of the pin is 5/8 of an inch. I went and pulled one of these from our warehouse to take this measurement.

view full answer...

Answer 5

You should be able to disassemble the Bolt-On Stainless Steel Spring Latch #SL716SS although nobody has tried and tested it for this specific purpose so I can't guarantee you this will absolutely work. I have added a link to a video review for…

view full answer...

Answer 6

The bolt/pin on the Bolt-On Stainless Steel Spring Latch part #SL716SS can travel up to 1-3/4" while the spring is fully compressed which will bring the pin flush to the end of the plate.

view full answer...

Answer 7

The Peterson Trailer Tail Light #421KRUS is a sealed waterproof unit, but the bulb will technically replaceable. However, removing the cover to gain access to the bulb will damage this seal and the light will no longer be waterproof, so I do advise…

view full answer...

Answer 8

No, there should only be one wire coming out of the Clear Utility Light, item #507-12. There is another wire inside that light, see photo at right, that is attached to the mounting hardware for grounding the light. This requires that the light be…

view full answer...

Answer 9

You'll need to first find the power and ground wire and then wire them to your battery through a switch as needed. If the lights are the part #507-12 that you referenced then this grounds through the mounting hardware so all you need is to run a…

view full answer...

Answer 10

Thanks for the pictures of your horse trailer's rear door. The part #2212 will work as a replacement for the hinges that you have. We have spring latches too like the part #SL716SS as well but do not have door seals.

view full answer...

Answer 11

The Peterson 440 series trailer lights typically have 4 screws at each of the corners of the lens that allow you to remove the lens and replace the bulb. It may be possible that you have a sealed version of these lights, in which case the bulb is…

view full answer...

Answer 12

I went and measured a Bolt-On Stainless Steel Spring Latch #SL716SS and found that the height of it would be 15/16 of an inch. Check out the picture I attached that shows this measurement.

view full answer...

Pin Length When Latched for the Bolt-On Stainless Steel Spring Latch # SL716SS

Product Page this Question was Asked From

Continue Researching