Horse Trailer Rear Door Hinge and Spring Latch Availability

Question

Question:

Will this part work on my 97 Exiss Horse trailer ?? Also looking for spring latches for the tack compartment and window and door seals if they exist.

asked by: Tabitha

0

Expert Reply:

Thanks for the pictures of your horse trailer's rear door. The part # 2212 will work as a replacement for the hinges that you have.

We have spring latches too like the part # SL716SS as well but do not have door seals.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Peterson Trailer Tail Light #421KRUS is a sealed waterproof unit, but the bulb will technically replaceable. However, removing the cover to gain access to the bulb will damage this seal and the light will no longer be waterproof, so I do advise…

view full answer...

Answer 2

The Peterson 440 series trailer lights typically have 4 screws at each of the corners of the lens that allow you to remove the lens and replace the bulb. It may be possible that you have a sealed version of these lights, in which case the bulb is…

view full answer...

Answer 3

I went and measured a Bolt-On Stainless Steel Spring Latch #SL716SS and found that the height of it would be 15/16 of an inch. Check out the picture I attached that shows this measurement.

view full answer...

Answer 4

No, there should only be one wire coming out of the Clear Utility Light, item #507-12. There is another wire inside that light, see photo at right, that is attached to the mounting hardware for grounding the light. This requires that the light be…

view full answer...

Answer 5

You'll need to first find the power and ground wire and then wire them to your battery through a switch as needed. If the lights are the part #507-12 that you referenced then this grounds through the mounting hardware so all you need is to run a…

view full answer...

Answer 6

I went and pulled a Bolt-On Stainless Steel Spring Latch #SL716SS from our warehouse and measure the dimension you are looking for and found it to be 1-7/8 inches. See the pic I attached, I added the dimension to the picture you submitted

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 12

If you're wanting to install the Timbren #TFR350SDJ on your 2022 Ford F-350 then you'll want to measure the distance from where your factory bump stops are installed down to the point of contact on the axle. The Timbren #TFR350SDJ are…

view full answer...

Horse Trailer Rear Door Hinge and Spring Latch Availability

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching