Haulmark Bargman Trailer Light Recommendation for a Lens Marked 30-84-022

Question

Question:

Hello I have a Haulmark trailer manufactured about 2000 I believe. The single lens stop/tail/turn light fixture is corroded at the contacts and Id like to replace the whole light fixture. The part number on the inside of the light is 30-84-022 and the fixture is about 5 1/4inch wide, 4 3/8inch tall, and about 2 or 2 1/8inch deep with a red lens. It is recessed and has two supply wires and a ground wire. I couldnt seem to find a replacement part number. Any help would be appreciated.

asked by: Will

0

Expert Reply:

You have an 84 series Bargman taillight assembly on your trailer. The correct replacement lens would be the part # 47-84-712.

expert reply by: Jameson C

0

Answer 1

If you aren't using the indicator lights and switches you mentioned you don't need to have them on your new range hood. So what you would want to do is measure the width and depth of your current range hood and then check out the link I…

view full answer...

Answer 2

For a Bargman 84 series tail light we currently offer the Replacement Lens for Bargman Tail Light #34-84-711 and the Enhanced-Height Lens for Bargman #47-84-712. The #34-84-711 is 5-5/8" long x 4-1/4" wide x 7/8" deep and I've…

view full answer...

Answer 3

Hello Thomas, thanks for reaching out. The Wheel Masters Wheel Covers #WM3160B0 will work on your 1996 F250 as long as it also uses 16" 8-lug wheels.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 12

Hey Michael! The Roadmaster Comfort Ride Leaf Spring Suspension Kit #RM82MR will fit your Wildwood X-Lite with underslung axles. We have confirmed this with Roadmaster. Most travel trailers and 5th wheels have overslung axles which is why you…

view full answer...

Haulmark Bargman Trailer Light Recommendation for a Lens Marked 30-84-022

Continue Researching