Bearing Kit for Lippert 4,400 lb Axles

Question

Question:

Which bearing kit do I need for Lippert 4400 axles? thanks

asked by: Bruce M

0

Expert Reply:

Hey Bruce! Thanks for the picture of your axle tag. Your 4,400 lb axle uses a #84 spindle with the standard 3,500 lb bearing combination. You can use the # BK2-100 or if you want the Lippert kit # LC55ZP. For USA made bearings we also have the Timken # TMK52VR.

expert reply by: Robin H

0

Robin H.

8/31/2026

Thanks for the photo. Your axles use the standard 3,500 lb bearing combination. If you want the Lippert bearing kit that is the # LC55ZP. For Timken it would be the # TMK52VR.

Answer 1

Hey Tom, thanks for reaching out. The bearings included in the #BK2-100 kit are supplied by TruRyde. They are not manufactured in the USA, but TruRyde has been a long-time supplier in the trailer industry and we've found their bearings, races,…

view full answer...

Answer 2

Hey Doug, welcome back! Yes, since you have a Lippert 4,000 lb axle the replacement Lippert hub/drum kit part #LC72DX would be correct for a replacement. Are you looking to have a spare on hand or is yours currently in need of replacing?

view full answer...

Answer 3

Hey Matthew! Thanks for the axle tag picture. Even though the capacity is 3,000 lbs it will still use the #84 spindle. The LCI35 is a 3,500 lb model designation so the Lippert Brake Drum and Hub Kit #LC72DX will work as a replacement. What kind of…

view full answer...

Answer 4

It sure is Chris and thanks for the information! The Lippert Brake Drum and Hub Kit item #LC72DX is designed for 3,500 lbs axles and has a 5 on 4-1/2 lug nut pattern. This hub is sold individually. It comes ready to be installed with pregreased…

view full answer...

Answer 5

Hey, Brent! We have just what you need. I reached out to Lippert to get the information about the hub you need and you will bee Lippert part #LC72DX. This is a hub and drum assembly that is pre-greases so the seal, inner, and outer bearings are…

view full answer...

Answer 6

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Bearing Kit for Lippert 4,400 lb Axles

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching