Fit Thule Hullavator to Roof Rack

Question

Question:

Hi there, I have an older Thule hullavator with roof clamps for a narrow roof rack. However, I now have new Thule wingbar evo racks on my car. What do I need to be able to attach the hullavator tracks to my car? I think I need a t slot adapter but not sure if I need another piece as well. Thank you!

asked by: Adrienne B

0

Expert Reply:

Hey Adrienne, if you have the older version of the Thule Hullavator # TH898 that did not come with mounting hardware for it to the top channels of a crossbar there isn't a way to adapt it so that it will fit that bar style unfortunately. That early version of the Hullavator only fit two bar types and did not fit top channels.

expert reply by: Jameson C

0

Answer 1

Hey Paul! You can use two Thule Hullavator Pro Kayak Roof Rack and Lift Assist w/ Tie-Downs #TH898 with the Rola Haul-Your-Might T3 Truck Bed Ladder Rack you got from us without needing to use any adapters, but you will need to space the towers on…

view full answer...

Answer 2

Make sure that you place the bottom section of the Thule Hullavator #TH898 as far up to the end cap of your crossbars as possible. This could be your issue. You can shift the crossbar around if that doesn't solve your problem. With the brackets…

view full answer...

Answer 3

For the Thule Hullavator part #TH898 the hardware that goes through the part #TH57BH is #853-5439, #TH93BW and #951061254.

view full answer...

Answer 4

The Thule Hullavator Pro Kayak Roof Rack #TH898 will either clamp around the Thule WingBar Evo Crossbars #TH711420 or can be held inside the channel. The Bar Mount Assembly #7521741001 included with the carrier allows for either style attachment to…

view full answer...

Answer 5

You will actually just use the square nuts that come with the Thule Hullavator Pro #TH898 to mount it on your Yakima JetStream bars (see attached photo). I have attached the installation instructions for you to reference for the installation as…

view full answer...

Answer 6

The Thule Hullavator load-assisted kayak carrier #TH898 will directly mount onto just about any roof rack bar shapes, including round, square, aero, elliptical, most factory crossbars, and most crossbars with top "T-slot" channels. Yakima…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Your 2017 Lance 1475 has the Dexter #10 torsion axle. The lift kit for that axle is #K71-707-01 like you referenced and will give you a lift of 2-5/8 inches.

view full answer...

Answer 9

The Go Power Portable Solar System #34282730 that you referenced should work great to keep the 12V battery in your Lancer camper topped off. In reality it's going to depend on just how much power you will be drawing (how many accessories you…

view full answer...

Answer 10

Hey John! To get your 4Runner lights working while flat towing you need the Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Way to 6-Way Coiled Adapter Cord #RM-15267. This kit comes with everything required, including the 7-way to…

view full answer...

Answer 11

I have a great option for you. When using the Stromberg Carlson Bike Bunk Trailer-Mounted Bike Rack Carrier for A-Frame Trailers #CC-275 there are a few parameters you will need to stay within. The bike rack needs to be travel trailer rated, fit a…

view full answer...

Answer 12

According to Yakima you'd unlock the twist plugs by using a coin to rotate them counter clockwise and from there you'd be able to pull them out to install the SKS kit part #Y07204.

view full answer...

Fit Thule Hullavator to Roof Rack

Product Page this Question was Asked From

Continue Researching