How Wide Is The Cutout For The Step On The etrailer Single Axle Trailer Fender w/ Side Steps HP93RR?

Question

Question:

How wide is the cut out for the step i have shorelander fenders and it has a 5inch wide plate

asked by: Bob H

0

ShoreLand'r Fender
(click to enlarge)

Expert Reply:

Hey Bob, thanks for reaching out. The cutout for the step on the etrailer Single Axle Trailer Fender # HP93RR is approximately 5-1/2" wide, so it will work just fine with your 5" wide ShoreLand'r fender plate. That gives you about 1/4" of clearance on each side, which is enough room for a clean fit without leaving a large gap around the step.

What do you haul on your ShoreLand'r?

expert reply by: Jesse M

0

etrailer Single Axle Trailer Fender w/ Side Steps - Black Plastic - 13" Wheels
(click to enlarge)

Answer 1

Thanks for the pics Kemo, they really helped! The CE Smith Single Axle Trailer Fenders #CE19504-2 are larger than what you currently have and use a different mounting style. Based on your setup, the CE Smith Fenders wouldn’t bolt onto your existing…

view full answer...

Answer 2

Hey Charles, when using the Mounting Brackets for Trailer Fender #CE26098G-2 to install the Fulton fender part #F008563 the position of the brackets really comes down to what will work best for your individual situation. I think going into the…

view full answer...

Answer 3

Hey Duane, Once the bearings are packed with grease and the hub is on the spindle you'll need to slowly pump grease into the spindle until you see it start to seep out of the outer bearing. Be sure to use a manual grease gun so the grease…

view full answer...

Answer 4

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 5

Hey Jim, From what I could find online, I believe of the Single Axle Trailer Fender w/ Backing Plate for 13" and 14" Wheels #HP79VR along with the Mounting Brackets for Trailer Fender #CE26098G-2 will work, but you'll need to verify…

view full answer...

Answer 6

We have a very close option with the #CE19503-2 which is off by only 1/4 of an inch to the measurements you listed. It measures 29-3/4 inch for the inside portion and 33-3/4 inch for the outside portion.

view full answer...

Answer 7

Hello JT, At this time we do not have mounting brackets that bolt up directly to the etrailer Single Axle Trailer Fender w/ Side Steps - Black Plastic - 13" Wheels - Qty 1 #HP93RR. I reached out to the team that in charge of our etrailer parts…

view full answer...

Answer 8

Hey Paul, I attached a picture that shows the dimensions of the bottom of the etrailer single axle fender part #HP93RR that you referenced for you to check out. I believe this will still work for you but you might compare them to your fender to make…

view full answer...

Answer 9

The etrailer Steel Jeep-Style Single-Axle Trailer Fender, part #HP76VR, is intended for weld-on installation on single-axle trailers with 13- to 15-inch tires. Because it is a weld-on item there is no hardware or mounting bracket supplied. We also…

view full answer...

Answer 10

I have a solution for you but #F008559 is not what you need because the mounting holes for this fender are on top not on the side like what you need and it's a slightly different style as well. For the exact same style of fender you want the…

view full answer...

Answer 11

Hi William; yes, I would expect the Fulton Single Axle Trailer Fenders #F008574-2 to be compatible with 205/75R14 tires. These are designed to work with 14" rims. I suppose if you mounted the fender incredibly low on top of the tire with no…

view full answer...

Answer 12

I went out to our warehouse to take a look at both the CE Smith Single Axle Trailer Fenders - 12" Grey #CE19502-2 and the larger 13" Black #CE19503-2. Both options represent the only color available from CE Smith in the respective sizes.…

view full answer...

How Wide Is The Cutout For The Step On The etrailer Single Axle Trailer Fender w/ Side Steps HP93RR?

Product Page this Question was Asked From

Continue Researching