Will Locking Endcaps for Vortex Aero Crossbars Fit Rhino-Rack Sportz Crossbars

Question

Question:

Do these locking end caps fit the new Rhino Sportz crossbars?

asked by: Ethan O

0

Expert Reply:

Hi Ethan; I'm sorry to say the Locking Endcaps for Vortex Aero Crossbars # RRVA-LEC4 do not fit the Sportz bars. Rhino-Rack does not have an option for locks that fit these crossbars at this time.

expert reply by: Robin H

0

Answer 1

Hey Rick, I wish I could say yes a Thule locking hitch pin would work with your Rhino Rack T-Load part #RTL002 but they are different sizes. The good news is the T-Load comes with a lock for the hitch pin so you won't need anything else.

view full answer...

Answer 2

The Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar #RTL002 does use the Hitch Lock #RRRBCA025.

view full answer...

Answer 3

As you can see in the diagram I provided, the tilt is adjustable up to about 45°. The tilt mechanism has a pin that can be used in two different positions to allow a roughly 15 or 30° degree tilt or the pin can be completely removed for the…

view full answer...

Answer 4

Yes! You can use both a kayak rack and a truck bed extender on your 2021 Jeep Gladiator with the Trail Rail system. Since the Access Lorado Soft, Roll-Up Tonneau Cover #A53VR leaves the stake pockets completely open, you will be able to install a way…

view full answer...

Answer 5

Hey Deb, You could just remove the load stops for the Rhino-Rack T-Load Hitch Mounted Load Assist and Support Bar #RTL002 and clamp on one kayak carrier like the Rhino-Rack Kayak Roof Rack w/ Tie-Downs #S512-S512X to the crossbar and the other to the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Hi Ethan; I'm sorry to say the Locking Endcaps for Vortex Aero Crossbars #RRVA-LEC4 do not fit the Sportz bars. Rhino-Rack does not have an option for locks that fit these crossbars at this time.

view full answer...

Answer 10

That's not a silly question Vanessa. The answer's no but I've heard way worse questions. The Progressive Dynamics Replacement Section item #PD4645V is the updated version and the only option to replace the converter in a Parallax Series…

view full answer...

Answer 11

Hello Justin, Looks like you were right on the money. I am showing with that information that it is a 3,500 pound axle so you will need the Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle #BK2-100. Getting things…

view full answer...

Answer 12

Yes the 4,000-lb leaf spring is compatible with a 3,500-lb axle. There are a couple of important measurements. Spacing from eye to eye on the spring when unloaded with no weight on the axle. Inner eye diameter of the spring roll Spring width from…

view full answer...

Will Locking Endcaps for Vortex Aero Crossbars Fit Rhino-Rack Sportz Crossbars

Product Page this Question was Asked From

Continue Researching