Will CE Smith Bunk Guide Ons Fit 2 by 3 inch Frame Rails

Question

Question:

My trailer rails are 2” wide X 3” deep. Will the CE27660 fit?

asked by: Mark

0

Expert Reply:

Hey Mark, yes the CE Smith Bunk-Style Guide-Ons for Boat Trailers # CE27660 that you referenced can fit on a trailer rail that is 2 inch by 3 inch like what you have. What kind of boat do you have?

expert reply by: Jameson C

0

Don R.

3/24/2026

These are ok but I am going to change mine to the post style. I want to be able to load in deeper water and that will make it easier for me and easier on my bunks.

Answer 1

Hi Shawn! You're dealing with a common issue when installing a MaxxAir II cover #MA76JR on a MaxxFan 4751KS, like the #MA00-04751KSX. Here’s the situation you're running into: -First, the MaxxFan lid opens almost vertical when fully opened…

view full answer...

Answer 2

Yes, if you wanted to paint the brackets of the CE Smith Bunk-Style Guide-Ons for Boat Trailers #CE27660 black you certainly could.

view full answer...

Answer 3

Since you mentioned wanting the most stability and not always being perfect when loading (understandably), I think the longer, 5 foot (60 inch) CE Smith Bunk-Style Guide-Ons for Boat Trailers #CE27600 is the best option as it will give you the most…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Will CE Smith Bunk Guide Ons Fit 2 by 3 inch Frame Rails

Product Page this Question was Asked From

Continue Researching