How Many MORryde X-Factor Crossmembers For 2018 Vengeance Triple Axle Toy Hauler
Updated 03/18/2026 | Published 03/07/2026
Products Featured in This Question
Question:
I have a 2018 Vengeance triple axle toy hauler. How many of these cross members do I need and where do I install them on a triple axle set up?
asked by: Wayne
Expert Reply:
Hey Wayne! The MORryde X-Factor Crossmember # MR33WR installs between your hangers. For the most stability, you will need a total of four since you have four sets of hangers. These are designed to work with the MORryde CRE, SRE, or stock suspension system.
Where are you headed once you get the crossmembers installed on your toy hauler?
(click to enlarge)
Tom
3/12/2026
Yes I put the Cross Members in along with other modifications, extremely happy with them and my other modifications. Made my fifth wheel much more rugged and reliable. I traveled all over the country and needed to reinforce everything I could to put the odds in my favor to withstand the ever changing road conditions. Make sure you buy all three cross members. Also I added Sumo Helper Springs and added Road Master Shock Absorbers. Also I Boxed the spring hangers and made triangle brackets for above each contact position on the frame and floor Joyces just above the spring hangars. I also have the Moreride heavy duty shackles and wet bolt system and Moreride equalizers. Yes on the surface it may seem over the top, but believe me it’s well worth the extra money and time.
Robin H.
3/12/2026
Ken
3/12/2026
I added these to my Cougar 5th wheel because I became aware of a few incidents where the hangers snapped off the frame. I looked at mine and noticed one hanger was slightly bent. Not only did the cross members solve the problem but made a noticeable improvement in towing the trailer. Highly recommended. On my tandem axle it took 3 cross members.
Randy
3/12/2026
The crossmembers worked well stiffened up the suspension big time . I think theses are a must for the big heavier units, they put less stress on mounting brackets for the suspension for the trailer.
David C.
3/12/2026
I installed the crossmembers on two of the three hangers on my Brinkley Z3100 fifth wheel. They made a tremendous improvement. It is most noticeable when you are making minor corrections. The sway that I used to experience is almost completely gone.
Product Page this Question was Asked From
MORryde X-Factor Crossmember for Standard Frame Hangers
- Accessories and Parts
- Trailer Suspension Parts
- Crossmember
- MORryde
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: MORryde X-Factor Crossmember for Standard Frame Hangers
- Q&A: Can Dexter EZ Flex Equalizer be Used with MORryde X-Factor Crossmember
- Search Results: progressive dynamics pd9160alv
- Video: Review of Victron RV Power Inverter - Inverter MultiPlus II Inverter Charger AC Outputs - VN73VR
- Search Results: morryde xfactor
- Search Results: rv steps
- Search Results: x factor
- Search Results: moryde x factor
- Search Results: rv leveling blocks
- Search Results: electric awning
- Q&A: Which Hangers Should MORryde X-Factor Crossmembers Install On
- Q&A: Pads To Protect The Bottom Of Stackable Plastic Leveling Blocks When On Rocky Terrain
- Q&A: Jack Pad Recommendation for Anderson Trailer Jack Block Bucket
- Q&A: Is There a Furrion Chill Cube Setup that Works as Both a Dump Setup and Through Ducts
- Video: MORryde X-Factor Crossmember Set Up - 2025 Grand Design Reflection Fifth Wheel
- Video: Review of MORryde StepBrush Boot Scraper StepAbove 2nd Generation - MR49RV
- Video: Review of Victron RV Power Inverter - Pure Sine Wave - VN68ZR
- Shop: Victron MultiPlus-II Inverter Charger with 1 AC Input - 2,400 Watts - 50 Amps - 12V - UL Listed
- Shop: Victron MultiPlus Pure Sine Wave Inverter Charger - 2,000 Watts - 50 Amps - 24V - UL Listed
- Shop: Victron MultiPlus-II Inverter Charger with 1 AC Input - 2,400 Watts - 50 Amps - 24V - UL Listed
- Shop: RV Camera
- Video: MORryde X-Factor Crossmember Install - 2023 Palomino Puma Unleashed 5W Toy Hauler
- Shop: Victron Phoenix VE.Direct Inverter - NEMA 5-15R - 400 Watts - 12V
- Shop: Victron MultiPlus Pure Sine Wave Inverter Charger - 1,000 Watts - 16 Amps - 12V
- Shop: Victron Phoenix VE.Direct Inverter - NEMA 5-15R - 1,000 Watts - 12V
- Video: MORryde X-Factor Crossmember Install - 2018 Highland Ridge Mesa Ridge Lite Fifth Wheel
- Shop: Suspension Enhancement
- Video: MORryde X-Factor Crossmember Installation - 2020 Grand Design Momentum 5W Toy Hauler
- Q&A: Does the X-Factor Crossmember for Standard Frame Hangers Require Longer Suspension Bolts?
- Q&A: Which MORryde X-Factor Can be Used with CRE3000 MORryde Equalizer Kit 2022 Grand Design Imagine
on Accessories and Parts
Tim
3/12/2026
Agree with the previous comment, you will need 4 of the cross members. Beware of any obstacles for the installation. We had a black tank drain line in the way of one of our cross members. So that required a set of their adapter brackets to lower the cross member.