What Would Cause Trailer Equalizer to be Tilted to One Side After Install of New Leaf Springs
Updated 03/05/2026 | Published 03/04/2026
Products Featured in This Question
Question:
I have a question about my equalizer and leaf springs. I’ve got a 2020 grand design momentum 29g. I have a Dexter EZ flex kit K71-654-00, MORryde suspension upgrade kit MR46ZR and 6000 lbs leaf spring e88SR installed. All items bought from etrailer. I’m trying to figure out why my equalizer and leaf springs look like this and what to do to fix it. It’s parked on flat ground and even moving it forward or back does not make it level out. It looks like most the weight is on the rear tire. It’s the same on both side. Any help would be appreciated.
asked by: Matthew P
(click to enlarge)
(click to enlarge)
Helpful Expert Reply:
Hey Matthew, what you you are experiencing is due to going with leaf springs that are too long and it forces the equalizer to kind of fold in on its self. I checked your order notes and you went with the part # e88SR which is a 26 inch long leaf spring for a 6k axle. So the correct spring that would fix the issue would be the part # e78SR which is 25-1/4 inches long instead. I know it sucks to have to buy new springs and redo all the work you did but it's unfortunately only way to fix it.
Sometimes a shorter equalizer from left to right can fix this but since you have the # K71-654-00 already and there isn't anything shorter this would not be the correct fix.
Product Page this Question was Asked From
Dexter E-Z Flex Equalizer Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
- Trailer Suspension Parts
- Equalizer Upgrade Kit
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Tandem Axle
- Dexter
more information >
Continue Researching
- Search Results: rv jack pads
- Search Results: camper jacks accessories and parts
- Search Results: camper jacks
- Search Results: heavy duty shackle
- Search Results: trailer leaf springs
- Search Results: add promo code
- Shop: CE Smith U-Bolt Kit for Mounting 5.2K to 7K, Round Trailer Axles - 7" Long U-Bolts - Zinc
- Shop: etrailer Rust-Resistant 5-Leaf Double Eye Spring for 6K Trailer Axles - 25-1/4" Long - Dacromet
- Shop: U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7-1/16" Long U-Bolts
- Shop: U-Bolt Kit for Mounting 5,200-lb to 7,000-lb, Round Trailer Axles - 7" Long U-Bolts
- Shop: Dexter Heavy-Duty Shackle Link for 1-3/4" Wide Double Eye Spring Suspension Kit - Qty 1
- Shop: Dexter E-Z Flex Suspension Kit - Double-Eye Springs - Tandem Axle - 6,000 lbs
- Q&A: Replacement Wet Bolt for MORryde Suspension Upgrade Kit
- Q&A: Replacement Leaf Springs and MORryde X-Factor Crossmember for 2021 Grand Design Imagine 2400BH
- Search Results: spring seats
- Q&A: Which Dexter EZ Flex Fits 2020 Grand Design Momentum 29G
- Q&A: Can I Use 4,000 lbs Springs to Replace 3,500 lbs Leaf Springs?
- Q&A: How to Choose Correct Replacement Leaf Springs and Equalizers for a 2021 Coachmen 259FKDS
- Q&A: Replacement Wet Bolt and Shackle Kit Compatible With Dexter EZ Flex Equalizer System
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/4" Long
- Q&A: Torque Spec for 1/2" U-Bolt
- Video: Review of the Replacement Wet Shoulder Bolt
- Video: Ultimate Overview of the CE Smith U-Bolt Kit for Mounting 5.2K to 7K, Round Trailer Axles
- Video: Let’s Check Out the CE Smith U-Bolt Kit for Mounting Round Trailer Axles
- Video: 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles Spec Review
- Video: Detailed Breakdown of the Shackle Strap
- Video: Feature Review Dexter Single Axle Heavy Duty Suspension Kit
- Article: How to Raise Your Travel Trailer Height
- Article: Double-Eye Trailer Suspension System Review
Matthew P.
3/5/2026
I spoke to your customer service before ordering and had measured my old springs before ordering. The old leaf springs were 26 inches as were the ones I ordered. After taking one off, I laid them side to side and they were the exact same length. I had talked to your customer service before to ask if it was ok to use e88RS because it had 6 levels of metal bars compared to the factory 5 levels of leafs that I was replacing. So did your rep give me the wrong advice on which leaf springs to order?