Replacement Bearing Kit for a 4400 Lbs Dexter Axle

Question

Question:

I have a grand design trailer with dexter 4400 pound axles. From the sticker on the axle it says Dex7665884 and S/N 134259950054. Do you have a bearing kit for that axle?

asked by: Scott K

0

Expert Reply:

Hey, Scott.

We have exactly what you need. The Dexter bearing kit part # DX86ER comes with everything that you need to replace the bearings, races, and seals. This kit is a per wheel set so you will need to order 2 for one axle.

What other maintenance are you getting done for your camper before camping season arrives?

expert reply by: Gwendolyn Y

0

DX86ER
(click to enlarge)

Answer 1

Hello Gilbert, thanks for reaching out. We do have brakes and hubs for Dexter 4,400 lb axles, but the sizing for these 4.4K axles can be funky depending when they were made. The best way to confirm what you need is with the casting number on the…

view full answer...

Answer 2

Hey Don. The correct grease seal for a Dexter 4,400 lbs axle is item #58846. It has a 1.719" inner diameter and 2.565" outer diameter. To replace all the bearings, races, seal, tang washer, and cotter pin you'll need the Dexter Bearing…

view full answer...

Answer 3

Based on the measurements you gave me it sounds like Grease Seal #168233 that you referenced is the one you need. It's a double lip grease seal that has an Inner diameter of 1.688" and an Outer diameter of 2.332". The #010-180-00 seal…

view full answer...

Answer 4

Keith, it appears so - but to be sure I'd recommend just confirming that your current brakes are 10" x 2 1/4", has a 4 bolt mounting flange, and all of the specs listed on the product page matches. If all that checks out, then yes the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

Hey Brandon, thanks for the information! You are correct. The Dexter Bearing Kit item #DX86ER is exactly what you'll need if your Keystone Cougar has Dexter 4,400 lbs axles. This kit is designed to replace one hubs worth of bearings, races, seal,…

view full answer...

Replacement Bearing Kit for a 4400 Lbs Dexter Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching