Installation Diagram for the Stromberg Carlson Repair Kit part # LG-146059

Question

Question:

if i buy kit will it work for keystone couger 06 model and do u just push out the u shaped pin then the rest comes apart ,is it spring loaded my question is if it is going to blow apart if i do it and also if lead jack goes does it mean both should be replaced at same time im doing this myself at home i can do it at a machine shop if need be

asked by: Todd C

0

Expert Reply:

If you have a Venture landing gear set on your 2006 Keystone Cougar the Stromberg Carlson repair kit part # LG-146059 would be the correct kit for you.

As you take the jack apart you should be able to see how it all comes apart and reinstalls with the new components. There isn't a set of installation instructions but I did attach a diagram that shows how all of the parts go together.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Leer 100XR isn't specifically listed by Pop and Lock but more than likely the #PAL9772 will fit. It requires a frameless, bonded glass door with a 1-1/8" center hole for a rotary latch. This particular kit would upgrade your existing…

view full answer...

Answer 2

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 3

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 4

Hey Jordan! Yes, the Global Link Vise Lock #295-000024, Global Link RV Entry Door Locking Latch #295-000019, and Replacement Cam Lock Cylinder #295-000005 can all use the same key. Just make sure you choose the keyed alike option for each one before…

view full answer...

Answer 5

Hi George, The Curt Replacement Lifting Nut part #C93NR is specifically designed for the Curt 28512 heavy-duty weld on jack so it will not work as a replacement for a Bulldog jack. Bulldog jack parts are typically model-specific so even if they look…

view full answer...

Answer 6

I linked the schematic diagram for Lead Jack Repair Kit #LG-146059 taken from the written instructions. The complete instructions will be sent to you in a separate link. The follow leg repair kit is part #LC146060 in case you need it.

view full answer...

Answer 7

You should need repair kit #LG-146059 for the lead leg and #LG-146060 for the follower leg. From the picture you sent in I was able to determine that you have a Venture landing gear set VMC900R.

view full answer...

Answer 8

Repair kit #LG-146059 contains 2 pins and the drive shaft all of which are for the top of the jack. To help I have included the written instructions below and also a diagram that points out the parts mentioned in the written instructions. The…

view full answer...

Answer 9

For your lead jack leg on your Lippert Venture Landing Gear VMC900R-327953, you will want to use the Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear #LC146059. As for a follow leg kit, you will want to use the Lippert Venture Follow…

view full answer...

Answer 10

You might be able to find a sticker on either leg that will tell you who the manufacturer is and what the part number is for the leg as well. If you aren't able to find that then you can try reaching out to Forest River with your VIN to see if…

view full answer...

Installation Diagram for the Stromberg Carlson Repair Kit part # LG-146059

Product Page this Question was Asked From

Continue Researching