What Kind of Ground Clearance Do I Need for the Fastway E2 Weight Distribution Trunnion System

Question

Question:

Hi there, Regarding the E2 weight distribution trunnion system, what is the min clearance of the L bar from the road to the bottom of the bar please? Thank you. Joe.

asked by: Joe M

0

Expert Reply:

Thank you for your question, Joe.

The Fastway E2 weight distribution trunnion bar systems don't have a minimum clearance. The trunnion bars are going to give you the most clearance vs the round bar systems.

Do you have a trailer that's super low to the ground and your worried about clearance?

expert reply by: Gwendolyn Y

0

Joe M.

11/14/2025

Hi Gwendolyn, Thank you for your reply. Yes I do have a low traveling trailer. the travel height once coupled to the vehicle from the road to the bottom of the A frame is 290mm (11.4 ") Thank you. Joe.

Gwendolyn Y.

11/17/2025

@JoeM A trunnion bar is definitely the way you want to go to get the most out of your clearance. For which one to get, it all depends on what your total tongue weight is. I've linked all the Fastway units using a trunnion bar below for you.

Helpful Links

dept-pg-weight_distribution_hitch-sf-wd_with_sway_control-pt-trunnion_bar-hs-fits_2_inch_hitch-pm-fastway.aspx

Answer 1

You are correct the 12V PWM Filter for RV Backup Camera Systems item #VGR64VR will solve your problem. The PWM Filter is basically a capacitor that provides your camera with the necessary power that GM has decided not to provide through their 7-Way…

view full answer...

Answer 2

In order to find the model number on the Furrion 2-in-1 Range Oven part #FSRE21SABL you will need to pull this out away from the cabinets and then look on the left hand side of the unit for a white sticker with barcode which should then display the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

The RV Propane Gas Detector part #RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a…

view full answer...

What Kind of Ground Clearance Do I Need for the Fastway E2 Weight Distribution Trunnion System

Continue Researching