Do You Have a Replacement Motor for a Ultra-Fab Electric A-Frame Jack?

Question

Question:

Do you have motor for ultra fab trailer jack Ultra 3502 model 38-944017

asked by: Rickey

0

Expert Reply:

Hey Rickey, thanks for the information. I am sorry but we do not a replacement motor for the Ultra-Fab Electric A-Frame Jack item # UF38-944017.

expert reply by: Jerred H

0

Jerred H.

12/1/2025

Hey Rickey, were you able to find a motor that works with your Ultra-Fab trailer jack? Knowing what solution you found could help others looking for the same part.

Answer 1

If your Ultra-Fab #UF38-944017 Powered Trailer Tongue Jack's motor still operates but the jack leg does not retract then odds are that one or more gear components in the jack are damaged. The motor itself is probably okay. We do offer a range of…

view full answer...

Answer 2

If you look at the provided photo, you can see an exploded diagram of the Ultra-Fab #UF38-944017 powered jack you mentioned. If you would reply with the number of the part you need, I would be happy to check availability for you.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Do You Have a Replacement Motor for a Ultra-Fab Electric A-Frame Jack?

Continue Researching