Will Valterra StayPut Tandem Trailer Tire Changing Ramp # VAL68MB Work w Curt Independent Suspension

Question

Question:

Will this work on a rv with curt independent suspension? thank you

asked by: Mitchell

0

Expert Reply:

Hey Mitchell, yes the Valterra StayPut Tandem Trailer Tire Changing Ramp # VAL68MB that you referenced will work with the Curt independent suspension you have and will still lift the trailer wheels up high enough to allow you to change it. How do you like the independent suspension?

expert reply by: Jameson C

0

Mitch

10/31/2025

I love the independent suspension! I left a Styrofoam cup on the bathroom sink and traveled 89 miles to a campground. when i arrived and set up the cup was still on the sink. The suspension handles very good and minimal bounce while on rough roads and trails. Thanks for answering my question about tire changing ramp. Thank you

Reply

Jameson C.

11/3/2025

@Mitch That's awesome! Yeah I imagine 9 times out of 10 with standard trailer suspension that cup would have fallen.

Reply

Answer 1

Gerald, the 12-ton Tallboy #PM94FR weighs about 37 lbs all-in, including the base plate, extensions, and carry bag. It’s a little heavy, but that’s the tradeoff for stability and steel construction - the 9-1/2 inch base plate and solid risers are…

view full answer...

Answer 2

Hey Tom, while we don't have a mounting bracket or anything designed to carry jacks like the part #VAL68MB one solution could be that you could store it in one of the storage compartments of your boat if you have room there? Would that work or…

view full answer...

Answer 3

Hey Mac! If you're using 2x4's the tallest option I have for you is the Ultra-Fab Leveling Blocks item #UF48-979052 that you were looking at. They're 1-3/8" tall and you're going to be limited to stacking them five high. This…

view full answer...

Answer 4

You do need more clearance between the overhang of your fifth wheel trailer and you bed rails. We recommend 6 inches or at the very least 4 inches if you are super careful. What you would want to do is raise the head of the fifth wheel as tall as it…

view full answer...

Answer 5

The Blaylock EZ Jack and Wheel Chock for Tandem-Axle Trailers #EZ-JACK can fit trailers with leaf springs. If you check out the picture I attached you can see it used on a leaf spring trailer just like yours.

view full answer...

Answer 6

That's a great question. The manufacturer doesn't exactly provide this information so I went out to our warehouse and did some tests with the Blaylock EZ Jack and Wheel Chock part #EZ-JACK for you. It looks like the highest point on the…

view full answer...

Answer 7

Hey Teo, we have a solution for you but we don't have any harnesses that work as both a tow bar lighting kit and a trailer wiring kit. So what you'd want is the Curt part #C96JR for the tow bar lighting and then for the trailer wiring…

view full answer...

Answer 8

Our selection of trailer tires in the 205/75-14 size with a D load range is limited to Kenda Karrie and Westlake. These both are considered higher quality radial options but the best one for your application will come down to your particular speed vs…

view full answer...

Answer 9

Hey Ian, are you asking about the fifth wheel prep package? If thats the case just look in the bed of the truck. If you see a square of pucks over the rear axle with one also in the center that's the OEM prep package. See the attached picture to…

view full answer...

Answer 10

Since you are not getting the 12V power when your truck is running, you most likely don't have a fuse issue as you stated their isn't a specified fuse or relay in the owners manual. The issue is that your truck is computerized even at the…

view full answer...