Availability of JR Products Type A Aluminum Curtain/Door Track

Question

Question:

I need to get a part from one of your manufacturers and they recommended you as a supplier. The Part number is 80201 by JR Products. We will need 4 of these expedited please.

asked by: Kimberly A

0

Expert Reply:

Hi Kimberly; we didn't have this part but I went ahead and added it to our site for you. It is the JR Products Type A Aluminum Curtain/Door Track # JR72MV (same as part 80201). You can select whatever shipping you need to get it as fast as possible when you check out.

expert reply by: Robin H

0

Aluminum Curtain/Door Track
(click to enlarge)

Robin H.

10/22/2025

Hi Kimberly, did you end up ordering the JR Products aluminum curtain track once it was added to the site? Knowing how the expedited shipping worked out could help others who need parts quickly.

Answer 1

I do have an option for you though we don't carry the exact Winnebago Left Hand Screen Door Latch you're looking for. That said, we do have some similar options such as the Bi-Directional Screen Door Latch part #37206-11865 which can be used…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The etrailer.com Electric Trailer Brake Kit #AKEBRK-7-SA and the Dexter Nev-R-Adjust Electric Brake Kit # 23-464-465 referenced in your question are both self-adjusting assemblies that will work to replace the existing Dexter brakes on your 7,000…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

Hey Michael! The Roadmaster Comfort Ride Leaf Spring Suspension Kit #RM82MR will fit your Wildwood X-Lite with underslung axles. We have confirmed this with Roadmaster. Most travel trailers and 5th wheels have overslung axles which is why you…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Availability of JR Products Type A Aluminum Curtain/Door Track

Product Page this Question was Asked From

Continue Researching