How to Determine Lug Nut Torque for Trailer Wheel

Question

Question:

Would you know the torque lbs of the rims on my hubs that I just bought?

asked by: Thomas A

0

Expert Reply:

Hey Thomas, that will depend on what size wheels you have and also what the wheels are made of.

expert reply by: Jameson C

0

Torque Chart
(click to enlarge)

Jameson C.

9/2/2025

Hey Thomas, did you find out the torque specs for your wheels? I'd love to hear what you discovered, as it could help others in a similar situation.

Answer 1

The portion you need to measure is not the cap, but the the hub bore. Remove the grease caps and measure the diameter of the opening the caps occupy. This is the hub bore. You will need an accurate measuring devices like a set of dial calipers that…

view full answer...

Answer 2

Hi Doug, The Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-440-2-EZ-1K uses a lithium complex grease so in this case the #L11390 would be compatible because they both share the same base. As long as the bases of the grease are the same…

view full answer...

Answer 3

The model 1980 Bearing Buddy simply means that they fit a 1.980 inch hub bore. There is one difference of note between Bearing Buddy Bearing Protectors #BB1980A (Chrome Plated) or #BB1980A-SS (Stainless Steel) and the Bearing Buddy Bearing Protectors…

view full answer...

Answer 4

When you are replacing bearings you do want to pack them prior to installing the new ones into your hub. This ensures that the grease actually gets pushed completely into the bearings so that they work properly and don't overheat. You can use a…

view full answer...

Answer 5

Grease can be added to the hub through an easily accessible grease fitting located in the center of the Bearing Buddy piston. Lubricant level can be checked by pressing on the edge of the piston. If you can rock or move the piston, the hub is…

view full answer...

Answer 6

There isn't a way to install zerk fittings on your spindle to make it an EZ lube spindle, but we do have Bearing Buddies which are designed for spindles like yours that do not have the zerk fittings to make installing grease in them easier. You…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

How to Determine Lug Nut Torque for Trailer Wheel

Product Page this Question was Asked From

Continue Researching