Where Can I Find Instructions For SumoSprings On My 2024 Toyota Land Cruiser?

Question

Question:

Hello Im looking at the Sumo Help[er springs Codess28F .They are to go on a 2024 Toyota Landcruiser can you send me directions so i can see how they get installed.

asked by: Edward V

0

Expert Reply:

Hey Edward,

The correct SumoSprings for your 2024 Toyota Land Cruiser are # SS28FJ. They are a no drill installation and I have attached the instructions below for you to see how they install. It is fairly simple, just removing the factory bump stops and installing these back in place. Feel free to let me know if you have any additional questions about the install.

Do you tow with the land cruiser or just looking for additional support?

expert reply by: Nick S

0

Edward V.

8/5/2025

I tow with it. A 20 ft geo pro rv. Just curious if it would affect the ride

Nick S.

8/5/2025

@EdwardV Out of all the rear suspension enhancements, the SumoSprings tend to affect the ride the least. Anything you additionally add to your suspension will change the ride in general, but the SumoSprings have the least effect. They ride better than airbags would.

Answer 1

Welcome back Matt. I checked with Air Lift their item #AL58FF kit won't work with your Land Cruiser. The coils are longer on the factory coil springs that come with the 2026 4Runner. The Air Lift item #AL58FF aren't big enough to expand and…

view full answer...

Answer 2

Hey Mike, yes we have the Air Lift LoadLifter part #AL75HF that is a confirmed fit for your 2026 Toyota 4Runner. This is actually listed as a fit for the 2025-2028 models as well. Are you planning on doing some towing? If you were also looking for a…

view full answer...

Answer 3

Hey Jeff, SumoSprings do not need to be touching the axle when unloaded. Having a bit of a gap while unloaded is totally normal. Giving your axle a bit of wiggle room before engaging the jounce spring will give you a bit more of a comfortable ride.…

view full answer...

Answer 4

Hey Kevin, if you were to run the minimum 5 psi requirement in the Air Lift kit part #AL57596 the ride quality would be the same as stock as the bags would essentially be totally empty. The 5 psi prevents the bags from deforming though which is why…

view full answer...

Answer 5

Hey Randy, welcome back and congrats on the new truck. For a 450 lbs - 500 lbs tongue weight, I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ90-00-0600. This system will let you back up with it installed and…

view full answer...

Answer 6

Hey Mike! We do have an option that weighs less than 70 lbs. The Blue Ox SwayPro Weight Distribution w/ Sway Control for 2" Hitch #BXW0550 weighs 50 lbs. This is designed to work with trailer tongue weights ranging from 350 lbs - 550 lbs. If you…

view full answer...

Answer 7

The SumoSprings Solo Custom Helper Springs like part #SSR-209-40 can be in contact with the jounce spring contact point without a load present. Depending on which kit you have, there is sometimes a spacer that will allow you to have either a slight…

view full answer...

Answer 8

Hey Andy, so the Old Man Emu springs part #ARB93FR that you referenced are considerably heavier springs than what came stock on your 2025 Toyota 4Runner so it will do a great job getting rid of the sag. These are rated for 260 lb per inch whereas OEM…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Where Can I Find Instructions For SumoSprings On My 2024 Toyota Land Cruiser?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching