Can Brophy Rope Ring Tie-Down Anchor Be Mounted Using Center Hole Only

Question

Question:

Is it necessary to use 2 screws to hold the outer black ring, or can you just attach with the 3/8 center bolt. I dont want to add any more holes in my wood bed. Thanks

asked by: Steve K

0

Expert Reply:

Hey Steve! You can mount the Brophy Rope Ring Tie-Down Anchor # RR09 using just the center hole. That outer bezel is plastic so it is basically there for aesthetics and isn't holding any weight. Just make sure the mounting hardware you choose and the mounting surface are able to handle the force and you're set.

What are you using the tie-downs for?

expert reply by: Robin H

0

Brophy Rope Ring Tie-Down Anchor
(click to enlarge)

Steve K.

8/5/2025

To secure Cushman Motor Scooter in bed of 1952 pickup truck.

Robin H.

8/6/2025

@SteveK I had to look that scooter up and that looks really cool. Are you a collector or do you like to work on old automobiles as a hobby?

Steve K.

8/6/2025

@RobinH Both

Robin H.

8/6/2025

@SteveK ah yeah, definitely helps if you can do the work yourself on the classic cars/trucks. If you need anything else don't hesitate to reach out.

Answer 1

The diameter of the install holes of the D-ring part #RR09 are 1/4 inch. Best option would be to use hardware that matches that diameter that also matches the material you want to install the ring to on your trailer.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Can Brophy Rope Ring Tie-Down Anchor Be Mounted Using Center Hole Only

Product Page this Question was Asked From

Continue Researching