Recommended Grease Seal w/ a 2.33 OD and a 1.5 ID

Question

Question:

Do you stock a grease seal with 2.33 OD, 1.5 Rubber ID, 1.75 Metal ID, 0.5 Depth? I will need two.

asked by: Randy W

0

Expert Reply:

Yes, we do and thanks for the measurements Randy. It's the Grease Seal SL150 item # SL150. These are sold individually.

What kind of trailer do you have?

expert reply by: Jerred H

0

Randy W.

5/15/2025

Excellent customer service, Jerrod! You even put the product right here below! I will definitely order them and make you my go-to supplier. The trailer is an old Magnolia Craft with fenders so rusty, I could barely make out the name. I have pictures, but I'm guessing 50's or 60's. Do you know which latch spring goes to the old Fulton No. 235 winch? I've restored it, but need this critical part.

Jerred H.

5/16/2025

@RandyW Thanks for the kind words Randy. Happy to help! I would love to take a look at those pics. You can send them to the email you receive this response from. I can look and see if we have some replacement fenders if you'd like. I would just need some measurements off of yours. I do not have a replacement latch spring for a old Fulton No. 235 winch and I couldn't find anything when I searched online. Best I can do is offer a replacement for you like item # F142306.

Answer 1

The best way to match up a seal is to determine the necessary inside and outside diameter of the grease seal. I'd need to know the diameter of the hub bore where the seal sits. Use a digital caliper, because a ruler or tape measure won't be…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Recommended Grease Seal w/ a 2.33 OD and a 1.5 ID

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching