Wiring Diagram for Replacement Solenoid on Superwinch

Question

Question:

I just bought and received the solenoid and it had no markings on any terminal or wiring diagram? Can you supply one? seems strange that it would have zero markings on it. Or even a picture of it on a winch wired up would help a ton. thanks Chris Lorenz

asked by: Chris L

0

Expert Reply:

Thank you for your question Chris!

I attached a wiring diagram of how the Superwinch gets wired up, it shows the solenoid part # SW90-12877 in the diagram. We do not have a diagram specifically for the solenoid.

Let me know if I can do anything else to help by commenting below.

expert reply by: Heather A

0

Chris L.

4/28/2025

Where is the attachment? Thanks Chris

Heather A.

4/30/2025

@ChrisL Shoot, the system didn't add it. I went ahead and emailed it to you in another email. Sorry about that.

Answer 1

The Electric tongue jack for a trailer is determined by the actual tongue weight of the trailer. Normally this is 10-15% of the total trailer weight when loaded, but a jack is one area where having something rating larger than needed will not cause…

view full answer...

Answer 2

Yes the Oil Seal #91030 is the correct seal for your 2018 DRV Mobile Suites with 9K axles. An oil seal can be used in a greased hub as long as it is the correct size and all the oil is removed since mixing oil and grease is not recommended. You can…

view full answer...

Answer 3

The Dexter brake assembly 023-217-00 is a 10 by 2-1/4 brake for 3,500 pound axles that fits a 4-bolt brake mounting flange. For replacements I recommend part #AKEBRK-35-SA that includes both sides. They're labeld to make the install easier and…

view full answer...

Answer 4

Thanks for the picture of what you have and the info you listed. The correct wheel you need is the part #AM20794 that you referenced.

view full answer...

Answer 5

There could be a few different things happening with your Curt Discovery Trailer Brake Controller part #C84VV. The first thing that could be happening is that you have a short on the red stop light switch wire. In order to rule this out you will need…

view full answer...

Answer 6

Thanks for reaching out! For your application you need the Replacement Motor for Kwikee Electric RV Steps #LC379147, as long as your steps were manufactured after 2005. If your steps were manufactured prior to 2005 then we need to get you a whole new…

view full answer...

Answer 7

I've edited a photo for you that shows the bolt hole pattern of the Buyers Products #337BP200 Swivel Pintle Hook. If you click the provided link, you can see a product description video featuring the pintle hook.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Wiring Diagram for Replacement Solenoid on Superwinch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching