How to Level a 5th Wheel Trailer that's Nose High w/ the Tow Vehicle
Updated 09/26/2025 | Published 04/22/2025 >
Products Featured in This Question
Question:
I have a 2015 cruiser Aire 30rfe, it has a Lippert 1621 pin box I need to lower my pin box height. My 2018 ram 2500 stock is high with puck system. My hitch is lowered all the way. of coarse its a slider. short wheel base less angle
asked by: Terry
Expert Reply:
What model of pin box do you currently have? The MORryde Cushioned 5th Wheel Pin Box # MR64VR you were looking at has a total height of 11.35" (pictured below) so you wouldn't see much of a difference from a standard pin box.
Unless you can mount that pin box in a higher set of bolt holes there's no way to adjust the the height difference of your 5th wheel trailer without raising the axles. This can be done by replacing the leaf spring hangers with longer ones, using a Correct Track lift kit like item # RR23QX, or by using an Over-Under conversion kit like item # K71-385-00 for 3" axles or item # K71-384-00 for 2-3/8" axles. The over under kits only work if your leaf springs are below your axles.
The easiest option out of these would be to use the Correct Track Kit item # RR23QX, which will raise your suspension either 1-1/4" or 2-1/4" in height.
Product Page this Question was Asked From
MORryde Cushioned 5th Wheel Pin Box for Up to 11.5K Trailers w/ Lippert 1621 and 1621HD
- 5th Wheel Pin Box
- Upgraded Pin Box
- Reduces Chucking
- 21000 lbs
- Rubber Spring Suspension
- Fixed Turret
- Lippert 1621
- Lippert 1621HD
- MORryde
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: jr products propane fittings
- Q&A: Plug Needed For A JR Products RV LP Gas Manifold # JR65CR
- Shop: Fifth Wheel Hitch
- Video: Review of JR Products Propane Fittings - Adapter Fittings - JR62ZR
- Video: Review of JR Products Propane Fittings - Quick Disconnect Y Splitter LP Gas - JR79MR
- Video: Review of JR Products Propane Fittings - 3 Port LP Gas Manifold - JR45CR
- Video: Review of JR Products Propane Fittings - Manifolds - JR32CR
- Q&A: Lift Kit Solution to Allow Fifth Wheel Trailer to Sit More Level When Towed
- Shop: JR Products Quick-Disconnect Propane Adapter Fitting - Male QD x 1/4" Male NPT
- Shop: JR Products RV LP Gas Manifold Hose Adapter - 1/2" x 1/4" NPT
- Shop: JR Products Quick Disconnect Y Splitter - Male QD x (2) Female QD
- Shop: JR Products RV LP Gas Manifold - 3 Port - Linear
- Shop: MB Sturgis Propane Adapter Fitting - 3/8" Male Flare x 1/4" Male NPT - Qty 1
- Shop: Propane Adapter Fitting - 3/8" Female SAE Flare x 1/4" Female NPT
- Shop: JR Products RV LP Gas Manifold Plug - 1/2"
- Search Results: rv range hoods accessories and parts
- Video: Review of the Curt Rota-Flex 5th Wheel Pin Box
- Video: The Low-Down on the Curt Rota-Flex 5th Wheel Pin Box
- Search Results: fifth wheel hitch
- Video: In-Depth Review of the Ventline Exterior Wall Vent for RV Range Hood
- Search Results: dexter 010~019~00
- Article: Fifth Wheel Trailer Hitch Information and Installation Tips
- Article: Is It Illegal to Leave My Hitch on My Truck?
- Search Results: 5th wheel pin box
- Q&A: How to Determine Correct Height Setting for 5th Wheel Hitch
- Q&A: How to Adjust the Height of a 5th Wheel Trailer Pin Box
- Search Results: battery vent cover
- Q&A: Can Reese Elite Hitch Install on Curt Adapter Rails for More Height on a 2021 Ford F-450 Puck System
- Shop: Truck Bed Bike Rack
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box



Jerred H.
9/26/2025
Hey, did you find a solution to adjust the height of your pin box? I'm asking because your experience could help others facing a similar challenge with their setup.