LED Tail Lights with a Plug-In Connector for a 2008 Bass Tracker- Trailstar Boat Trailer

Question

Question:

I am looking to replace ST-36 RH. Optronics ST-37 LH. Optronics Do you have an exact replacement in LED with a plug in? If so, what are the numbers.

asked by: Ronnie Y

1

Helpful Expert Reply:

We do have the lights you are looking for. For the right hand side use Aero Pro Submersible LED Trailer Tail Light # STL36RPG. It is the same light only with a 2-wire molded plug.

The matching left hand side is # STL37RPG.

expert reply by: Michael H

1

Answer 1

You can use the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers - Rear Axle #AL88298 with an in-bed hitch system like your B&W Turnoverball Gooseneck hitch #BWGNRK1110 (with overload springs) or #BWGNRK1100…

view full answer...

Answer 2

An Air Lift air spring kit that fits your 1997 Ford F-350 would not be considered an overload spring. Overload springs are a separate spring that attaches to the rear leaf spring pack that looks like it only connects in the middle of the pack and not…

view full answer...

Answer 3

Hey Case! I double checked with Firestone and found that none of the air bags that fit the 1996 F-250/F-350 are compatible with an in-bed hitch. The brackets install in the same location as the brackets for a gooseneck. If you want to install the…

view full answer...

Answer 4

So the now-discontinued Bulldog gooseneck 947533 will not fit your 1997 Ford F-350 unfortunately, as there isn't a mounting kit of any weight capacity that will allow it to fit your truck. So the best option available is a new gooseneck hitch…

view full answer...

Answer 5

If you look at your rear leaf springs, and see an extra leaf as shown in the diagram, you have the overload spring option. For a 1997 F350 with overload springs, you'd need the B and W Turnover Ball #BWGNRK1110. If your truck does NOT have the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

LED Tail Lights with a Plug-In Connector for a 2008 Bass Tracker- Trailstar Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching