Would the Curt Front Hitch part # 31432 fit a 2013 Jeep Wrangler With a MBRP Front Hitch

Question

Question:

I have 2013 rubicon. Does the hitch attach to the frame rail on the drivers side where the vacuum pump is mounted. Ive already relocated it and cut off welded mount to put on a mbrp bull bar. Would I be able to add the hitch if its the same location using longer bolts.

asked by: Mike

0

Expert Reply:

To see how the Curt Front Hitch part # 31432 would install on your 2013 Jeep Wrangler Rubicon check out the picture I attached. Hopefully you can tell if it will interfere with your MBRP bull bar.

This hitch wasn't test for compatibility with that bar so I cannot safely say if it would fit or not, especially considering the modifications you've already made.

expert reply by: Jameson C

0

click to enlarge

Answer 1

This combination has not been tested since both Curt and Draw-Tite list their front mounted hitches as only being compatible with factory bumpers. That being said it looks like they wouldn't be using the same mounting hole in the frame, but would…

view full answer...

Answer 2

Hey Dave, between the Draw Tite front hitch part #65069 and the Curt #31432 I would go with the Draw Tite as it has higher weight capacities and also currently it is priced better! Is this for a plow?

view full answer...

Answer 3

Thanks for the picture of the front end of your 2015 Jeep Wrangler Unlimited, based on that we know that the Draw Tite front hitch part #65069 is a confirmed fit and will work well. I attached an install video for this hitch for you to check out as…

view full answer...

Answer 4

On a 7-Way connector the suggested minimum wire gauge for the White (ground) wire, the Red or Black (power) wire, and the Blue (brake power) wire is 12 gauge. The minimum wire gauge for the remaining Green (right turn/brake) wire, the Yellow (left…

view full answer...

Answer 5

Front hitches and base plate kits typically use the same install points the vehicle frame so you would have to remove the front hitch or if you happened to have an aftermarket bumper there may be a solution. If the aftermarket bumper on your Wrangler…

view full answer...

Answer 6

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 7

For your 2015 Jeep Wrangler the front hitch I would recommend is the Draw Tite part #65069 as it has the highest capacities and the lowest price.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hi John, Sadly SmartPlug does not offer the female end of the SM22YB as a separate replacement part. If that end is damaged, the complete SmartPlug Angled RV Power Cord, part #SM22YB, would need to be replaced. The cord does come with a 1 year…

view full answer...

Would the Curt Front Hitch part # 31432 fit a 2013 Jeep Wrangler With a MBRP Front Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching