What Hub do I Need to Replace My DICO 40825 Hub on My Boat Trailer?
Updated 10/27/2025 | Published 03/11/2025 >
Products Featured in This Question
Question:
I need a replacement for a DICO 40825 hub off a boat trailer the spindle is 1 1/16 then steps up to 1 1/4 where the seal goes
asked by: Mike B
Expert Reply:
Hello Mike,
I am happy to get you into the right trailer hub. I am not able to find any information on the DICO 40825. From the measurements you provided it sounds like you have a straight spindle so both your inner and outer bearing are 1.063" I.D. making them bearing # L44649, which means you have a 2,000 pound axle. So you will want the Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-2-G-EZ-2K which is a 5 on 4 1/2" bolt pattern (for 4 on 4 bolt pattern # AKIHUB-440-2-G-2K). The issue that I am running into is that the grease seal is a 1.50" ID and not 1.25" like you measured. I attached an image so you can double check your measurements, it helps to use a digital caliper like # PTW80157 to get the most accurate measurement.
Please confirm the measurements by commenting below so I can ensure we are getting you the right fit. Also, if you are getting a 1.25" at the seal, I would like to know the age of the trailer. Sometime with older boat trailers they do not make the hubs for it which results in needing a new axle. I appreciate your time, and look forward to hearing back from you.
Product Page this Question was Asked From
CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased - Threaded
- Trailer Hubs and Drums
- Idler Hub
- Pre-Greased
- Standard
- L44643 / L44643
- Standard Grade
- For 2500 lbs Axles
- 1/2 Inch Stud
- 4 on 4 Inch
- 10 Inch Wheel
- 12 Inch Wheel
- 13 Inch Wheel
- CE Smith
more information >
Continue Researching
- Search Results: trailer tires and wheels
- Q&A: 5.30R12 Highway Rated Trailer Tire and Wheel Options for Saltwater Use
- Shop: Taskmaster 5.30R12 Radial Trailer Tire w/ 12" Vesper Silver Mod Wheel - 4 on 4 - LR C
- Video: Review of Taskmaster Trailer Tires and Wheels - Tire with Wheel - TA69QR
- Q&A: Do the Taskmaster 5.30R12 Radial Trailer Tire and Wheel Come Balanced?
- Q&A: Could CE Smith Trailer Axle Have New Holes Drilled at 40 inches Apart
- Shop: CE Smith Trailer Axle Beam with Studded Hubs - 5 on 4-1/2" - 54" Long - 1.8K
- Shop: Kenda 5.30-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: Steel Spoke Trailer Wheel - 12" x 4" Rim - 4 on 4 - Galvanized Finish
- Shop: Taskmaster 5.30R12 Radial Trailer Tire - Load Range C
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Search Results: trailer winch
- Search Results: winch cable
- Shop: Lippert Spindle Nut Kit w/ Round Washer - For 2,200-lb to 4,400-lb Axles
- Search Results: castle nut
- Search Results: l44649
- Search Results: l44649 / l44649 trailer hubs and drums
- Search Results: trailer bearings races seals caps
- Video: Review of Lippert Spindle Nut Kit - LC95RP
- Video: Feature Review CE Smith Trailer Hub Assembly w/ Carrying Case for 2,500-lb Axles
- Video: Review of Lippert Trailer Bearings Races Seals Caps - Dust Cap and Rubber Plug - LC37RP
- Video: Review of Dutton-Lainson Trailer Winch - Standard Hand Winch - DL14627
- Video: Comprehensive Review: Dutton-Lainson Hand Winch-DL14527
- Video: CE Smith Trailer Hub Assembly w/ Carrying Case for 2,700-lb Axles Review
- Q&A: Replacement Boat Trailer Idler Hub with 4-1/4" Depth and 1-1/16" Spindle
- Q&A: Replacement Winch for a Discontinued Fulton K1550 Winch
- Q&A: Looking for Grease Cap With OD Slightly Larger than 1.98 Inches
- Q&A: How to Pick Out Replacement Dust Cap for Trailer Hub
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs



Kate F.
10/27/2025
Hey Mike, were you able to recheck those spindle and seal measurements on your boat trailer hub? Once you confirmed them, did one of the 2,000‑lb hub assemblies end up fitting correctly? Your update could make it easier for others trying to match older trailer hubs.