What Bulldog Jack is Used in the etrailer Protective Cover Video

Question

Question:

what jack is in the video

asked by: Paul

0

Expert Reply:

Hey Paul,

You're looking at the Bulldog Jack # BD500199 that we installed the etrailer Protective Cover # e59VV on in our video.

expert reply by: Jon G

0

Bud M.

12/15/2025

Hey Paul, how did things go with the Bulldog jack and the protective cover from the video? Your experience could point others in the right direction.

Answer 1

You will need a different converter charger if you are going to lithium batteries, which is what I believe you are asking. The right one will depend on how many amp hours you need though, like the 100 amp-hour #34282738. I have added a link below to…

view full answer...

Answer 2

The Lippert Motor Home Entry Screen Door Bubble Slider Panel - Frosted #LC234101 measures to your required size at 12 x 12-inches. This part is clear, and it can be trimmed is necessary.

view full answer...

Answer 3

Hi Scott, thanks for reaching out. A great replacement for the 3,500-lb Lippert jack on your Jayco 32BHDS is the etrailer Electric Trailer Jack – A-Frame – 18" Lift – 3,500 lbs #e23ZV. It’s a bolt-on swap with the same capacity, upgraded…

view full answer...

Answer 4

There was indeed a recall on the Lippert Smart Jack Electric Trailer Jack part #LC643589. It sounds like you have a pre-recall version but in order to confirm you can look on the back of the jack for a sticker on the stem with a serial number. If…

view full answer...

Answer 5

Hello Bruce, yes it can. The etrailer Electric Trailer Jack #e55ZV can be rotated to the size and the bolts will still line up. We have this jack on one of our trailers here at the shop and I have checked and verified it can be rotated.

view full answer...

Answer 6

I have a complete replacement jack option for you, but the buttons on your Lippert Smart Jack #LC643589 are not replaceable so the only option is a complete replacement. If your jack is still within the 1-year warranty period then I recommend…

view full answer...

Answer 7

Welcome back Michael! I have not hear any issues with the etrailer Electric Trailer Jack w/ 7-Way - Drop Leg - A-Frame - 18" Lift - 5K #e74GV working with a 2025 Ram 1500. So far, this has been a Ford issue most of the time, but brand new GM…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The best solution as you alluded to is to bypass the factory "Smart Tow" trailer package which is what is responsible for only sending power to the 12 volt pin when the vehicle is in gear. This is actually pretty easy to do and we have a…

view full answer...

Answer 10

I do have some options for you but there isn't a plug under the dash for a trailer brake controller on a 2023 Chevrolet Traverse. Therefore, if you want to use a traditional dash mounted trailer brake controller you must hardwire which requires…

view full answer...

Answer 11

I'm guessing it is approximately 3-3/8" across if you measured it. Unfortunately there are no options that will slide in because it won't line up correctly, and everything is designed to fit a 3" tongue so it is too wide to mount an…

view full answer...

Answer 12

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

What Bulldog Jack is Used in the etrailer Protective Cover Video

Product Page this Question was Asked From

Continue Researching