Wire Sizes for the Hopkins Endurance Easy-Pull Harness

Question

Question:

What size are individual the wires in this product? 14, 16,18, 22 guage?

asked by: Don C

0

Expert Reply:

Don, the Hopkins Endurance Easy-Pull Harness # HM38134 has 18 AWG wires for the brown, green, and yellow wires, and 16 AWG for the white ground wire.

expert reply by: Bryce D

0

Lazer S.

12/15/2025

Hey Don, did the wire sizes on the Hopkins Easy-Pull harness work out for your setup? Knowing how it matched up could help others choosing connectors for similar wiring. Your update could make it easier for the next person with the same question.

Don C.

12/17/2025

@LazerS worked perfectly, I love the design

Lazer S.

12/17/2025

@DonC Nice! Glad we could help! : ) And the Hopkins Easy-Pull is definitely popular due to its design. Really does help get a grip on it when you are unplugging! Let us know if there is anything else we can help with!

Answer 1

The Hopkins Endurance Easy-Pull Harness w/ 4-Pole Flat Connector #HM38134 you referenced has 18 gauge wires for the brown (taillight), green (right turn and brake), and yellow (left turn and brake) wires. The white (ground) is a 16 gauge wire.…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Gary, thanks for reaching out. No, nothing is missing from the #C96GJ kit. Curt uses the term “T-Connector” pretty broadly for a lot of their plug-and-play harnesses, even when they are not a true tee-style splitter like you were expecting. On…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Wire Sizes for the Hopkins Endurance Easy-Pull Harness

Continue Researching