Axle-Less Suspension Recommendation for a 2025 InTech Flyer Pursue Trailer

Question

Question:

Which axle-less suspension do you recommend for a 2025 Intech Flyer Pursue. Pull vehicle is a Ford F150 4x4

asked by: Jeff R

0

Expert Reply:

Hey Jeff, thanks for reaching out!

It looks like your InTech Flyer Pursue has a 2,200 lb GVWR so for your application I recommend the 2.2K Heavy Duty Timbren Axle-Less Trailer Suspension # ASR1THDS02 so you get the right amount of suspension help. Then from there you just need 2 of the Easy Grease Trailer Idler Hub Assembly # AKIHUB-545-35-EZ-K and you'll be set!

expert reply by: Jon G

0

Jeff

10/17/2024

If i plan to carry more than the 2200#, can i go to the 3500#, or are there other factors i need to consider?

Jon G.

10/17/2024

@Jeff You can go with the 3,500 lb Kit # A35RS545 (which comes with the idler hubs too) but it's important to note that the axle isn't always the limiting factor - a lot of times the axles is rated for more than the GVWR of the trailer, and it's the trailer frame itself that is the limiting factor.

Answer 1

You can install Timbren Axle Less kits like the part #A35RS545 on aluminum frame trailers but it would be recommended to use like a rubber spacer/isolator to prevent galvanic corrosion. We don't have anything specific we can recommend but you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 10

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Axle-Less Suspension Recommendation for a 2025 InTech Flyer Pursue Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching