Does 2024 Kia EV9 Have Brake Controller Wiring Under Dash

Question

Question:

Hi. I have a 2024 Kia EV9 and a Tekonsha P2 brake controller. What wiring adaptor do I need? Thanks Scott

asked by: Scott A

0

Expert Reply:

Hey Scott, it looks like there is a brake controller connector under the dash of your 2024 Kia EV9 that you can wire to your P2 part # 90885 but we don't have a connector for it yet. What you can do is contact a Kia dealer to get their install pigtail for brake controllers and then wire it directly to your brake controller.

expert reply by: Jameson C

0

Scott A.

10/15/2024

I think they left me the pigtail. I can send you a picture of it if that helps? I'm wondering if all I need is the Telluride or Palisade one? I think it might be the same.

Jameson C.

10/15/2024

@ScottA Gotcha, so the vehicle came with a brake controller install harness? Most likely you need to plug that into your vehicle after hardwiring it to your P2.

Scott A.

10/15/2024

The part number on the pigtail is GENESIS T6F67 AC060 HYNUNDAI S8F67 AC060 KIA S9F67 AC060

Jameson C.

10/15/2024

@ScottA That's good to know, we don't have a harness yet for a plug and play install though.

Answer 1

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 2

Hey Dianne, what you need is a dog bone adapter to go from 50 amp to 30 amp like the Camco Power Grip part #CAM55175. This will plug into the RV park's 50 amp power source and connect it safely to your 30 amp power setup. Having more amperage…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Does 2024 Kia EV9 Have Brake Controller Wiring Under Dash

Continue Researching