Shank for Elite Weight Distribution Hitch
Updated 01/12/2026 | Published 09/07/2024
Products Featured in This Question
Question:
I currently have an Elite weight distribution hitch with a 2 shank. Im wanting to replace just the hitch using my equipment. So Im needing a 8 hitch with a 2.5 shank and 2 vertical. Im pulling a 26 ft travel trailer, Im thinking 14,000 lbs rating my tongue weight is 700lbs. What Im finding is that configuration but real heavy duty rating, way over what I need. My actual loaded trailer weight is under 10,000. Do you stock something that would work for me?. Regards JT.
asked by: Jt K
Expert Reply:
Hi Jt; so you're looking for a replacement shank for your Elite weight distribution hitch that fits a 2-1/2" hitch correct? And you want the distance from the hitch pin hole to the adjustment holes to be to be 8" as well? I'm assuming when you say 2 vertical do you mean 2" wide where it fits in the channel on the head which is the standard.
If I'm right about what you're asking you can use the Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop # EQ90-02-4700. This fits a 2-1/2" hitch, has your 8" measurement, and is the standard 2" wide for the WDH channel. This has a max rise of 7" and max drop of 3". The capacity isn't something to worry about as long as it is high enough for the trailer. Shank capacity does not impact the performance of the system so being overrated is fine. If you need a larger rise/drop the # EQ90-02-4900 is also available with a 10" rise/6" drop.
Product Page this Question was Asked From
Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- 700 lbs TW
- 800 lbs TW
- 900 lbs TW
- 1000 lbs TW
- 1200 lbs TW
- 1300 lbs TW
- Fits 2-1/2 Inch Hitch
- Equal-i-zer
- Square - 3 Inch Drop
- Square - 7 Inch Rise
- Equal-i-zer
more information >
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Weight Distribution Hitch for 2026 Chevy Silverado 3500 Towing Brinkley Z Air 297
- Article: 5 Things to Know About Weight Distribution Hitches
- Q&A: Shank For Fastway e2 Weight Distribution That Fits 2-1/2 Inch Hitch Receiver
- Q&A: Can You Convert to 2-1/2 Inch Shank From 2 Inch With Reese Weight Distribution Hitch
- Q&A: Does Using Gen-Y Capture Plate for Pullrite Hitch Also Require Using Pullrite Capture Plate
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Q&A: Exterior Wall Vent Needed For A Furrion RV Range Hood
- Q&A: Is it Possible to Use Too High Rated of a Weight Distribution System
- Article: Trailer Wiring Diagrams
- Q&A: Where Are Bulletproof Hitches Made?
- Article: Guide to Choosing the Best Truck for 5th-Wheel Towing
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Types of Trailer Hitches: How and Why to Use Each
Robin H.
1/12/2026
Hey JT, how did the Equal-i-zer shank work out with your Elite weight distribution hitch and 26-foot trailer? Your experience could point others toward the right setup for similar towing needs.